Enter an option: 2

Available interfaces:

1 - WAN (lagg0.4090 - dhcp, dhcp6)
2 - LAN (lagg0.4091 - static)
3 - OPT1 (ix0)
4 - OPT2 (ix1)

Enter the number of the interface you wish to configure: 3

Enter the new OPT1 IPv4 address.  Press <ENTER> for none:
> 192.168.50.1

Subnet masks are entered as bit counts (as in CIDR notation) in pfSense.
e.g. 255.255.255.0 = 24
     255.255.0.0   = 16
     255.0.0.0     = 8

Enter the new OPT1 IPv4 subnet bit count (1 to 31):
> 24

For a WAN, enter the new OPT1 IPv4 upstream gateway address.
For a LAN, press <ENTER> for none:
> 

Enter the new OPT1 IPv6 address.  Press <ENTER> for none:
> 

Do you want to enable the DHCP server on OPT1? (y/n) n

Do you want to revert to HTTP as the webConfigurator protocol? (y/n) n

Please wait while the changes are saved to OPT1...
 Reloading filter...
 Reloading routing configuration...
 DHCPD...

The IPv4 OPT1 address has been set to 192.168.50.1/24

Press <ENTER> to continue.
Netgate XG-7100 - Netgate Device ID: 9143791338acbc987796

*** Welcome to pfSense 2.4.5-RELEASE (amd64) on pfSense ***

 WAN (wan)       -> lagg0.4090 -> 
 LAN (lan)       -> lagg0.4091 -> v4: 192.168.25.1/24
 OPT1 (opt1)     -> ix0        -> v4: 192.168.50.1/24
 OPT2 (opt2)     -> ix1        -> 

 0) Logout (SSH only)                  9) pfTop
 1) Assign Interfaces                 10) Filter Logs
 2) Set interface(s) IP address       11) Restart webConfigurator
 3) Reset webConfigurator password    12) PHP shell + pfSense tools
 4) Reset to factory defaults         13) Update from console
 5) Reboot system                     14) Enable Secure Shell (sshd)
 6) Halt system                       15) Restore recent configuration
 7) Ping host                         16) Restart PHP-FPM
 8) Shell

Enter an option: 5


pfSense will reboot. This may take a few minutes, depending on your hardware.
Do you want to proceed?

    Y/y: Reboot normally
    R/r: Reroot (Stop processes, remount disks, re-run startup sequence)
    S: Reboot into Single User Mode (requires console access!)
    F: Reboot and run a filesystem check
    Enter: Abort

Enter an option: y

pfSense is rebooting now.
Waiting (max 60 seconds) for system process `vnlru' to stop... done
Waiting (max 60 seconds) for system process `bufdaemon' to stop... done
Waiting (max 60 seconds) for system process `syncer' to stop... 
Syncing disks, vnodes remaining... 1 0 0 done
All buffers synced.
Uptime: 3m41s
ix1: link state changed to DOWN

Google, Inc.
Serial Graphics Adapter 11/06/15
SGABIOS $Id: sgabios.S 8 2010-04-22 00:03:40Z nlaredo $ (wenwang@localhost.localdomain) Fri Nov  6 15:52:10 UTC 2015
Term: 156x38
O4 0























          __                               
   _ __  / _|___  ___ _ __  ___  ___       
  | '_ \| |_/ __|/ _ \ '_ \/ __|/ _ \      
  | |_) |  _\__ \  __/ | | \__ \  __/      
  | .__/|_| |___/\___|_| |_|___/\___|      
  |_|                                      
                                                                           
                                                                           
 +============Welcome to pfSense===========+   __________________________  
 |                                         |  /                       ___\ 
 |  1. Boot Multi User [Enter]             | |                      /`     
 |  2. Boot [S]ingle User                  | |                     /    :-|
 |  3. [Esc]ape to loader prompt           | |      _________  ___/    /_ |
 |  4. Reboot                              | |    /` ____   / /__    ___/ |
 |                                         | |   /  /   /  /    /   /     |
 |  Options:                               | |  /  /___/  /    /   /      |
 |  5. [K]ernel: kernel (1 of 2)           | | /   ______/    /   /       |
 |  6. Configure Boot [O]ptions...         | |/   /          /   /        |
 |                                         |     /          /___/         |
 |                                         |    /                         |
 |                                         |   /_________________________/  
 +=========================================+
                                          

/boot/kernel/kernel text=0x18bcad0 data=0xb9fcb8+0x4fcc70 syms=[0x8+0x1a7090+0x8+0x1a7ac1]
/boot/entropy size=0x1000
Booting...
KDB: debugger backends: ddb
KDB: current backend: ddb
Copyright (c) 1992-2020 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 11.3-STABLE #233 2c992b2181a(factory-RELENG_2_4_5): Tue Mar 24 15:26:54 EDT 2020
    root@buildbot1-nyi.netgate.com:/build/factory-crossbuild-245-amd64/obj/amd64/kkVaWThR/build/factory-crossbuild-245-amd64/sources/FreeBSD-src/sys/pfSense amd64
FreeBSD clang version 8.0.1 (tags/RELEASE_801/final 366581) (based on LLVM 8.0.1)
VT(vga): resolution 640x480
CPU: Intel(R) Atom(TM) CPU C3558 @ 2.20GHz (2200.07-MHz K8-class CPU)
  Origin="GenuineIntel"  Id=0x506f1  Family=0x6  Model=0x5f  Stepping=1
  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Features2=0x4ff8ebbf<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,SDBG,CX16,xTPR,PDCM,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,TSCDLT,AESNI,XSAVE,OSXSAVE,RDRAND>
  AMD Features=0x2c100800<SYSCALL,NX,Page1GB,RDTSCP,LM>
  AMD Features2=0x101<LAHF,Prefetch>
  Structured Extended Features=0x2294e283<FSGSBASE,TSCADJ,SMEP,ERMS,NFPUSG,MPX,PQE,RDSEED,SMAP,CLFLUSHOPT,PROCTRACE,SHA>
  Structured Extended Features3=0x2c000000<IBPB,STIBP,ARCH_CAP>
  XSAVE Features=0xf<XSAVEOPT,XSAVEC,XINUSE,XSAVES>
  IA32_ARCH_CAPS=0x1<RDCL_NO>
  VT-x: PAT,HLT,MTF,PAUSE,EPT,UG,VPID,VID,PostIntr
  TSC: P-state invariant, performance statistics
real memory  = 10737418240 (10240 MB)
avail memory = 8203603968 (7823 MB)
Event timer "LAPIC" quality 600
ACPI APIC Table: <CORE   COREBOOT>
WARNING: L1 data cache covers less APIC IDs than a core
0 < 1
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
FreeBSD/SMP: 1 package(s) x 4 core(s)
ioapic0: Changing APIC ID to 2
ioapic0 <Version 2.0> irqs 0-23 on motherboard
SMP: AP CPU #1 Launched!
SMP: AP CPU #3 Launched!
SMP: AP CPU #2 Launched!
Timecounter "TSC-low" frequency 1100035788 Hz quality 1000
ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE.
ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_bss_fw, 0xffffffff806a64a0, 0) error 1
ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE.
ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_ibss_fw, 0xffffffff806a6550, 0) error 1
random: entropy device external interface
ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE.
ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_monitor_fw, 0xffffffff806a6600, 0) error 1
iwi_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE.
iwi_bss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_bss_fw, 0xffffffff806cd6c0, 0) error 1
iwi_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE.
iwi_ibss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_ibss_fw, 0xffffffff806cd770, 0) error 1
iwi_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE.
iwi_monitor: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_monitor_fw, 0xffffffff806cd820, 0) error 1
wlan: mac acl policy registered
kbd0 at kbdmux0
000.000022 [4213] netmap_init               netmap: loaded module
module_register_init: MOD_LOAD (vesa, 0xffffffff812ce960, 0) error 19
random: registering fast source Intel Secure Key RNG
random: fast provider: "Intel Secure Key RNG"
mlx5en: Mellanox Ethernet driver 3.5.2 (September 2019)
nexus0
vtvga0: <VT VGA driver> on motherboard
cryptosoft0: <software crypto> on motherboard
padlock0: No ACE support.
acpi0: <CORE COREBOOT> on motherboard
acpi0: Power Button (fixed)
hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 24000000 Hz quality 950
Event timer "HPET" frequency 24000000 Hz quality 550
Event timer "HPET1" frequency 24000000 Hz quality 440
Event timer "HPET2" frequency 24000000 Hz quality 440
Event timer "HPET3" frequency 24000000 Hz quality 440
Event timer "HPET4" frequency 24000000 Hz quality 440
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
cpu2: <ACPI CPU> on acpi0
cpu3: <ACPI CPU> on acpi0
atrtc0: <AT realtime clock> port 0x70-0x77 on acpi0
atrtc0: Warning: Couldn't map I/O.
atrtc0: registered as a time-of-day clock, resolution 1.000000s
Event timer "RTC" frequency 32768 Hz quality 0
attimer0: <AT timer> port 0x40-0x43,0x50-0x53 irq 0 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1808-0x180b on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> irq 18 at device 6.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pci1: <processor> at device 0.0 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> mem 0xdfe00000-0xdfe1ffff irq 20 at device 14.0 on pci0
pci2: <ACPI PCI bus> on pcib2
ix0: <Intel(R) PRO/10GbE PCI-Express Network Driver, Version - 3.2.12-k> port 0x2000-0x201f mem 0xdf900000-0xdf9fffff,0xdfc00000-0xdfc03fff irq 16 at device 0.0 on pci2
ix0: Using MSI-X interrupts with 5 vectors
ix0: Ethernet address: 8c:dc:d4:a8:15:e8
ix0: PCI Express Bus: Speed 5.0GT/s Width x4
ix0: netmap queues/slots: TX 4/2048, RX 4/2048
ix1: <Intel(R) PRO/10GbE PCI-Express Network Driver, Version - 3.2.12-k> port 0x2020-0x203f mem 0xdfa00000-0xdfafffff,0xdfc04000-0xdfc07fff irq 19 at device 0.1 on pci2
ix1: Using MSI-X interrupts with 5 vectors
ix1: Ethernet address: 8c:dc:d4:a8:15:e9
ix1: PCI Express Bus: Speed 5.0GT/s Width x4
ix1: netmap queues/slots: TX 4/2048, RX 4/2048
pcib3: <ACPI PCI-PCI bridge> mem 0xdfe20000-0xdfe3ffff irq 22 at device 16.0 on pci0
pci3: <ACPI PCI bus> on pcib3
pcib4: <ACPI PCI-PCI bridge> mem 0xdfe40000-0xdfe5ffff irq 23 at device 17.0 on pci0
pci4: <ACPI PCI bus> on pcib4
ahci0: <Intel Denverton AHCI SATA controller> port 0x3020-0x3027,0x3028-0x302b,0x3000-0x301f mem 0xdfe74000-0xdfe75fff,0xdfe7c000-0xdfe7c0ff,0xdfe7a000-0xdfe7a7ff irq 21 at device 20.0 on pci0
ahci0: AHCI v1.31 with 5 6Gbps ports, Port Multiplier supported
ahcich1: <AHCI channel> at channel 1 on ahci0
ahcich3: <AHCI channel> at channel 3 on ahci0
ahcich4: <AHCI channel> at channel 4 on ahci0
ahcich5: <AHCI channel> at channel 5 on ahci0
ahcich6: <AHCI channel> at channel 6 on ahci0
xhci0: <Intel Denverton USB 3.0 controller> mem 0xdfe60000-0xdfe6ffff irq 19 at device 21.0 on pci0
xhci0: 32 bytes context size, 64-bit DMA
usbus0 on xhci0
usbus0: 5.0Gbps Super Speed USB v3.0
pcib5: <ACPI PCI-PCI bridge> irq 16 at device 22.0 on pci0
pci5: <ACPI PCI bus> on pcib5
pcib0: no PRT entry for 0.22.INTB
ix2: <Intel(R) PRO/10GbE PCI-Express Network Driver, Version - 3.2.12-k> mem 0xde000000-0xde1fffff,0xde400000-0xde403fff irq 16 at device 0.0 on pci5
ix2: Using MSI-X interrupts with 5 vectors
ix2: Ethernet address: 00:08:a2:0e:a5:91
mdio0: <MDIO> on ix2
e6000sw0: <Marvell 88E6190> on mdio0
e6000sw0: single-chip addressing mode
miibus0: <MII bus> on e6000sw0
e1000phy0: <Marvell 88E1000 Gigabit PHY> PHY 1 on miibus0
e1000phy0:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
miibus1: <MII bus> on e6000sw0
e1000phy1: <Marvell 88E1000 Gigabit PHY> PHY 2 on miibus1
e1000phy1:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
miibus2: <MII bus> on e6000sw0
e1000phy2: <Marvell 88E1000 Gigabit PHY> PHY 3 on miibus2
e1000phy2:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
miibus3: <MII bus> on e6000sw0
e1000phy3: <Marvell 88E1000 Gigabit PHY> PHY 4 on miibus3
e1000phy3:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
miibus4: <MII bus> on e6000sw0
e1000phy4: <Marvell 88E1000 Gigabit PHY> PHY 5 on miibus4
e1000phy4:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
miibus5: <MII bus> on e6000sw0
e1000phy5: <Marvell 88E1000 Gigabit PHY> PHY 6 on miibus5
e1000phy5:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
miibus6: <MII bus> on e6000sw0
e1000phy6: <Marvell 88E1000 Gigabit PHY> PHY 7 on miibus6
e1000phy6:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
miibus7: <MII bus> on e6000sw0
e1000phy7: <Marvell 88E1000 Gigabit PHY> PHY 8 on miibus7
e1000phy7:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
e6000sw0: switch is ready.
etherswitch0: <Switch controller> on e6000sw0
ix2: netmap queues/slots: TX 4/2048, RX 4/2048
e6000sw0port1: link state changed to UP
e6000sw0port2: link state changed to DOWN
e6000sw0port3: link state changed to DOWN
ix3: <Intel(R) PRO/10GbE PCI-Express Network Driver, Version - 3.2.12-k> mem 0xde200000-0xde3fffff,0xde404000-0xde407fff irq 10 at device 0.1 on pci5
e6000sw0port4: link state changed to DOWN
ix3: Using MSI-X interrupts with 5 vectors
e6000sw0port5: link state changed to DOWN
e6000sw0port6: link state changed to DOWN
e6000sw0port7: link state changed to DOWN
e6000sw0port8: link state changed to DOWN
ix3: Ethernet address: 00:08:a2:0e:a5:92
ix3: netmap queues/slots: TX 4/2048, RX 4/2048
pcib6: <ACPI PCI-PCI bridge> irq 17 at device 23.0 on pci0
pci6: <ACPI PCI bus> on pcib6
pcib0: no PRT entry for 0.23.INTB
ix4: <Intel(R) PRO/10GbE PCI-Express Network Driver, Version - 3.2.12-k> mem 0xde600000-0xde7fffff,0xdea00000-0xdea03fff irq 17 at device 0.0 on pci6
ix4: Using MSI-X interrupts with 5 vectors
ix4: Ethernet address: 00:08:a2:0e:a5:93
ix4: netmap queues/slots: TX 4/2048, RX 4/2048
ix5: <Intel(R) PRO/10GbE PCI-Express Network Driver, Version - 3.2.12-k> mem 0xde800000-0xde9fffff,0xdea04000-0xdea07fff irq 10 at device 0.1 on pci6
ix5: Using MSI-X interrupts with 5 vectors
ix5: Ethernet address: 00:08:a2:0e:a5:94
ix5: netmap queues/slots: TX 4/2048, RX 4/2048
pci0: <simple comms> at device 24.0 (no driver attached)
sdhci_pci0: <Intel Denverton eMMC 5.0 Controller> mem 0xdfe77000-0xdfe77fff,0xdfe78000-0xdfe78fff irq 16 at device 28.0 on pci0
sdhci_pci0: 1 slot(s) allocated
mmc0: <MMC/SD bus> on sdhci_pci0
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
pci0: <memory> at device 31.2 (no driver attached)
pci0: <serial bus> at device 31.5 (no driver attached)
uart0: <Non-standard ns8250 class UART with FIFOs> port 0x3f8-0x3ff irq 19 flags 0x10 on acpi0
uart0: console (115200,n,8,1)
uart1: <Non-standard ns8250 class UART with FIFOs> port 0x2f8-0x2ff irq 18 on acpi0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xc0fff,0xee800-0xeffff on isa0
ppc0: cannot reserve I/O port range
est0: <Enhanced SpeedStep Frequency Control> on cpu0
est1: <Enhanced SpeedStep Frequency Control> on cpu1
est2: <Enhanced SpeedStep Frequency Control> on cpu2
est3: <Enhanced SpeedStep Frequency Control> on cpu3
Timecounters tick every 1.000 msec
ugen0.1: <0x8086 XHCI root HUB> at usbus0
uhub0: <0x8086 XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0
mmcsd0: 31GB <MMCHC BJTD4R 0.3 SN 7A64FE68 MFG 12/2017 by 21 0x0000> at mmc0 50.0MHz/8bit/65535-block
mmcsd0boot0: 4MB partion 1 at mmcsd0
mmcsd0boot1: 4MB partion 2 at mmcsd0
mmcsd0rpmb: 4MB partion 3 at mmcsd0
uhub0: 8 ports with 8 removable, self powered
Trying to mount root from ufs:/dev/ufsid/5e7b6fd79c04e57d [rw]...
Configuring crash dumps...
Using /dev/label/swap0 for dump device.
/dev/ufsid/5e7b6fd79c04e57d: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/ufsid/5e7b6fd79c04e57d: clean, 6799011 free (4427 frags, 849323 blocks, 0.1% fragmentation)
Filesystems are clean, continuing...
Mounting filesystems...
random: unblocking device.

        __
 _ __  / _|___  ___ _ __  ___  ___
| '_ \| |_/ __|/ _ \ '_ \/ __|/ _ \
| |_) |  _\__ \  __/ | | \__ \  __/
| .__/|_| |___/\___|_| |_|___/\___|
|_|


Welcome to pfSense 2.4.5-RELEASE...

No core dumps found.
...ELF ldconfig path: /lib /usr/lib /usr/lib/compat /usr/local/lib /usr/lib/engines /usr/local/lib /usr/local/lib/ipsec /usr/local/lib/perl5/5.30/mach/CORE
32-bit compatibility ldconfig path:
done.
>>> Removing vital flag from php72... done.
External config loader 1.0 is now starting... mmcsd0s1 mmcsd0s1a mmcsd0s1b
Launching the init system...Updating CPU Microcode...
CPU: Intel(R) Atom(TM) CPU C3558 @ 2.20GHz (2200.07-MHz K8-class CPU)
  Origin="GenuineIntel"  Id=0x506f1  Family=0x6  Model=0x5f  Stepping=1
  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Features2=0x4ff8ebbf<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,SDBG,CX16,xTPR,PDCM,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,TSCDLT,AESNI,XSAVE,OSXSAVE,RDRAND>
  AMD Features=0x2c100800<SYSCALL,NX,Page1GB,RDTSCP,LM>
  AMD Features2=0x101<LAHF,Prefetch>
  Structured Extended Features=0x2294e283<FSGSBASE,TSCADJ,SMEP,ERMS,NFPUSG,MPX,PQE,RDSEED,SMAP,CLFLUSHOPT,PROCTRACE,SHA>
  Structured Extended Features3=0xac000400<MD_CLEAR,IBPB,STIBP,ARCH_CAP,SSBD>
  XSAVE Features=0xf<XSAVEOPT,XSAVEC,XINUSE,XSAVES>
  IA32_ARCH_CAPS=0x69<RDCL_NO,SKIP_L1DFL_VME,MDS_NO>
  VT-x: PAT,HLT,MTF,PAUSE,EPT,UG,VPID,VID,PostIntr
  TSC: P-state invariant, performance statistics
Done.
...... done.
Initializing.................. done.
Starting device manager (devd)...done.
Loading configuration......done.
..............................Updating configuration...done.
Checking config backups consistency...done.
Setting up extended sysctls...done.
padlock0: No ACE support.
aesni0: <AES-CBC,AES-XTS,AES-GCM,AES-ICM> on motherboard
coretemp0: <CPU On-Die Thermal Sensors> on cpu0
coretemp1: <CPU On-Die Thermal Sensors> on cpu1
coretemp2: <CPU On-Die Thermal Sensors> on cpu2
coretemp3: <CPU On-Die Thermal Sensors> on cpu3
Setting timezone...done.
Configuring looplo0: link state changed to UP
back interface...done.
Starting syslog...done.
Starting Secure Shell Services...done.
Configuring switch...done.
Setting up interfaces microcode...done.
Configuring loopback interface...done.
Creating wireless clone interfaces...done.
Configuring LAGG interfaces...done.
Configuring VLAN interfaces...done.
Configuring QinQ interfaces...done.
Configuring IPsec VTI interfaces...done.
Configuring WAN interface...done.
Configuring LAN interface...done.
Configuring OPT1 interface...done.
Configuring OPT2 interface...done.
Configuring CARP settings...done.
Syncing OpenVPN settings...done.
Configuring firewall......done.
Starting PFLOG...done.
Setting up gateway monitors...done.
Setting up static routes...done.
Setting up DNSs...
Starting DNS Resolver...done.
Synchronizing user settings...done.
Starting webConfigurator...done.
Configuring CRON...done.
Starting NTP time client...done.
Starting DHCP service...done.
Starting DHCPv6 service...done.
Configuring firewall......done.
Generating RRD graphs...done.
Starting syslog...done.
Starting CRON... done.
pfSense 2.4.5-RELEASE amd64 Tue Mar 24 15:25:53 EDT 2020
Bootup complete

FreeBSD/amd64 (pfSense.localdomain) (ttyu0)

Netgate XG-7100 - Netgate Device ID: 9143791338acbc987796

*** Welcome to pfSense 2.4.5-RELEASE (amd64) on pfSense ***

 WAN (wan)       -> lagg0.4090 -> 
 LAN (lan)       -> lagg0.4091 -> v4: 192.168.25.1/24
 OPT1 (opt1)     -> ix0        -> 
 OPT2 (opt2)     -> ix1        -> 

 0) Logout (SSH only)                  9) pfTop
 1) Assign Interfaces                 10) Filter Logs
 2) Set interface(s) IP address       11) Restart webConfigurator
 3) Reset webConfigurator password    12) PHP shell + pfSense tools
 4) Reset to factory defaults         13) Update from console
 5) Reboot system                     14) Enable Secure Shell (sshd)
 6) Halt system                       15) Restore recent configuration
 7) Ping host                         16) Restart PHP-FPM
 8) Shell

Enter an option: