U-Boot 2018.03-devel-18.12.3-gc9aa92c-dirty (Oct 07 2021 - 18:20:55 -0300)

Model: Netgate 1100
       CPU     1200 [MHz]
       L2      800 [MHz]
       TClock  200 [MHz]
       DDR     750 [MHz]
DRAM:  1 GiB
Comphy chip #0:
Comphy-0: USB3          5 Gbps
Comphy-1: PEX0          2.5 Gbps
Comphy-2: SATA0         6 Gbps
SATA link 0 timeout.
AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
flags: ncq led only pmp fbss pio slum part sxs
PCIE-0: Link up
Consoles: EFI console  sdhci@d8000: 1
    Reading loader env vars from /efi/freebsd/loader.env3235f with page size 256Setting currdev to disk0p2:total 4 MiB
FreeBSD/arm64 EFI loader, Revision 3.0
(Thu Nov 13 10:35:51 UTC 2025 root@pfsense-build-release-aarch64-2.eng.atx.netgate.com)eth0: neta@30000 [PRIME]
Hit any key to stop autoboot:  0
\  Command line arguments: loader.efit!
   Image base: 0x7000000netgate-1100.dtb
   EFI version: 2.70720-sg1100.dtb
   EFI Firmware: Das U-Boot (rev 0.00)tb
   Console: efi,comconsole (0).dtb
   Load Path: /\armada-3720-sg1100.dtb
   Load Device: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/eMMC(1)/eMMC(0)/HD(2,GPT,b554fde6-0678-11ef-856a-0b605a9f0465,0x84000,0x20000)
Trying ESP: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/eMMC(1)/eMMC(0)/HD(2,GPT,b554fde6-0678-11ef-856a-0b605a9f0465,0x84000,0x20000)
Setting currdev to disk0p2: at 07000000 ...
Trying: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/eMMC(1)/eMMC(0)/HD(1,GPT,b554fde6-0678-11ef-856a-0b605a9f0465,0x28,0x82000)
Setting currdev to disk0p1:ady
Trying: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/eMMC(1)/eMMC(0)/HD(3,GPT,b554fde6-0678-11ef-856a-0b605a9f0465,0xa4000,0xdea000)
Setting currdev to zfs:pfSense/ROOT/default_20241127091912_20251230150047:
Loading /boot/defaults/loader.confault_20241127091912:
Loading /boot/defaults/loader.conf
Loading /boot/device.hints
Loading /boot/loader.conf
Loading /boot/loader.conf.lua
Loading /boot/loader.conf.local
|
   _ __  / _|___  ___ _ __  ___  ___      _
  | '_ \| |_/ __|/ _ \ '_ \/ __|/ _ \   _| |_
  | |_) |  _\__ \  __/ | | \__ \  __/  |_   _|
  | .__/|_| |___/\___|_| |_|___/\___|    |_|
  |_|


+-- Welcome to Netgate pfSense Plus ---+
|                                      |
|  1. Boot Multi user [Enter]          |
|  2. Boot Single user                 |
|  3. Escape to loader prompt          |
|  4. Reboot                           |
|  5. Cons: Dual (Serial primary)      |   __________________________
|                                      |  /                       ___\
|  Kernel:                             | |                      /`
|  6. kernel (1 of 1)                  | |                     /    :-|
|                                      | |      _________  ___/    /_ |
|  Options:                            | |    /` ____   / /__    ___/ |
|  7. Boot Options                     | |   /  /   /  /    /   /     |
|  8. Boot Environments                | |  /  /___/  /    /   /      |
+--------------------------------------+ | /   ______/    /   /  _    |
  Autoboot in 0 seconds. [Space] to pause /   /          /   / _| |_  |
Loading kernel...                                                      |
/boot/kernel/kernel off=0 text=0x318 text=0xd21bf8 text=0xb47ec0 data=0x1b9500 |data=0x0+0x2cf000 0x8+0x1acc10+0x8+0x1c9ea2 (@0xffff000000000000-0xffff000002078ac8)
Loading configured modules...
/boot/entropy size=0x1000
can't find '/etc/hostid'
/boot/kernel/opensolaris.ko off=ffff00000207a000 text=0x19e6 text=0xc18 data=0x4d8+0x1a030 0x8+0xfa8+0x8+0x871
/boot/kernel/zfs.ko off=ffff0000020b9000 text=0xabfe8 text=0x234b50 data=0x3cbf0+0xae804 0x8+0x374d0+0x8+0x305de|
Using DTB provided by EFI at 0x8000000.
---<<BOOT>>---
GDB: current port: uart
KDB: debugger backends: ddb gdb
KDB: current backend: ddb
WARNING: DTB version is 6.4 while kernel expects 6.12, please update the DTB in the ESP
Copyright (c) 1992-2025 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 16.0-CURRENT #39 plus-RELENG_25_11-n256500-a43915e7ef55: Mon Dec  1 19:13:31 UTC 2025
    root@pfsense-build-release-aarch64-2.eng.atx.netgate.com:/var/jenkins/workspace/pfSense-Plus-snapshots-25_11-main/obj/aarch64/HBRSF4R0/var/jenkins/workspace/pfSense-Plus-snapshots-25_11-main/sources/FreeBSD-src-plus-RELENG_25_11/arm64.aarch64/sys/pfSense arm64
FreeBSD clang version 19.1.7 (https://github.com/llvm/llvm-project.git llvmorg-19.1.7-0-gcd708029e0b2)
VT: init without driver.
real memory  = 1073680384 (1023 MB)
avail memory = 987521024 (941 MB)
Starting CPU 1 (1)
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
random: unblocking device.
ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE.
ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_bss_fw, 0xffff00000026d5a4, 0) error 1
ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE.
ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_ibss_fw, 0xffff00000026d65c, 0) error 1
ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE.
ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_monitor_fw, 0xffff00000026d714, 0) error 1
iwi_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE.
iwi_bss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_bss_fw, 0xffff00000026d7cc, 0) error 1
iwi_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE.
iwi_ibss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_ibss_fw, 0xffff00000026d884, 0) error 1
iwi_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE.
iwi_monitor: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_monitor_fw, 0xffff00000026d93c, 0) error 1
random: entropy device external interface
wlan: mac acl policy registered
kbd0 at kbdmux0
ofwbus0: <Open Firmware Device Tree>
simplebus0: <Flattened device tree simple bus> on ofwbus0
simplebus1: <Flattened device tree simple bus> on simplebus0
ofw_firmware0: <OFW Firmware Group> on ofwbus0
simple_mfd0: <Simple MFD (Multi-Functions Device)> mem 0x13800-0x138ff,0x13c00-0x13c1f on simplebus1
simple_mfd1: <Simple MFD (Multi-Functions Device)> mem 0x18800-0x188ff,0x18c00-0x18c1f on simplebus1
psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0
smccc0: <ARM SMCCC v1.1> on psci0
netgate0: <Netgate 1100>
netgate0: version: 0.1
gic0: <ARM Generic Interrupt Controller v3.0> mem 0x1d00000-0x1d0ffff,0x1d40000-0x1d7ffff,0x1d80000-0x1d81fff,0x1d90000-0x1d91fff,0x1da0000-0x1dbffff irq 28 on simplebus1
gpio0: <Armada 37x0 North Bridge GPIO Controller> mem 0x13800-0x138ff,0x13c00-0x13c1f irq 29,30,31,32,33,34,35,36,37,38,39,40 on simple_mfd0
gpiobus0: <OFW GPIO bus> on gpio0
gpio1: <Armada 37x0 South Bridge GPIO Controller> mem 0x18800-0x188ff,0x18c00-0x18c1f irq 41,42,43,44,45 on simple_mfd1
gpiobus1: <OFW GPIO bus> on gpio1
gpioregulator0: <GPIO controlled regulator> on ofwbus0
a37x0-xtal0: <Marvell Armada 3700 Oscillator> mem 0x13800-0x138ff,0x13c00-0x13c1f on simple_mfd0
generic_timer0: <ARMv8 Generic Timer> irq 0,1,2,3 on ofwbus0
Timecounter "ARM MPCore Timecounter" frequency 12500000 Hz quality 1000
Event timer "ARM MPCore Eventtimer" frequency 12500000 Hz quality 1000
a37x0_tbg0: <Marvell Armada 3700 time base generators> mem 0x13200-0x132ff on simplebus1
a37x0_nb_periph_driver0: <marvell,armada-3700-nb-periph-clock> mem 0x13000-0x130ff on simplebus1
a37x0_sb_periph_driver0: <marvell,armada-3700-sb-periph-clock> mem 0x18000-0x180ff on simplebus1
smbios0: <System Management BIOS>
smbios0: Entry point: v2.1 (32-bit), Version: 3.0
cpulist0: <Open Firmware CPU Group> on ofwbus0
cpu0: <Open Firmware CPU> on cpulist0
pmu0: <Performance Monitoring Unit> irq 4 on ofwbus0
spi0: <Armada 37x0 SPI controller> mem 0x10600-0x10fff irq 6 on simplebus1
iichb0: <Marvell Armada 37x0 IIC controller> mem 0x11000-0x11023 irq 7 on simplebus1
iicbus0: <OFW I2C bus> on iichb0
iic0: <I2C generic I/O> on iicbus0
uart0: <Marvell Armada 3700 UART> mem 0x12000-0x12017 irq 9,10,11 on simplebus1
uart0: console (115200,n,8,1)
gpioc0: <GPIO controller> at pins 0-35 on gpiobus0
gpioc1: <GPIO controller> at pins 0-29 on gpiobus1
mvneta0: <NETA controller> mem 0x30000-0x33fff irq 14 on simplebus1
mvneta0: version is 10
mdio0: <MDIO> on mvneta0
mdioproxy0: <MII/MDIO proxy, MDIO side> on mdio0
e6000sw0: <Marvell 88E6341> on mdio0
e6000sw0: multi-chip addressing mode (0x1)
e6000sw0: CPU port at 0
e6000sw0: fixed port at 0
e6000sw0: PHY at port 1
miibus0: <MII bus> on e6000sw0
e1000phy0: <Marvell 88E1000 Gigabit PHY> PHY 17 on miibus0
e1000phy0:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
e6000sw0: PHY at port 2
miibus1: <MII bus> on e6000sw0
e1000phy1: <Marvell 88E1000 Gigabit PHY> PHY 18 on miibus1
e1000phy1:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
e6000sw0: PHY at port 3
miibus2: <MII bus> on e6000sw0
e1000phy2: <Marvell 88E1000 Gigabit PHY> PHY 19 on miibus2
e1000phy2:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
e6000sw0: switch is ready.
etherswitch0: <Switch controller> on e6000sw0
mvneta0: Ethernet address: f0:ad:4e:08:6d:cc
xhci0: <Generic USB 3.0 controller> mem 0x58000-0x5bfff irq 16 on simplebus1
xhci0: 32 bytes context size, 32-bit DMA
xhci0: xECP capabilities <PROTO,PROTO>
usbus0 on xhci0
ehci0: <Marvell Integrated USB 2.0 controller> mem 0x5e000-0x5efff irq 17 on simplebus1
usbus1: EHCI version 1.0
usbus1 on ehci0
sdhci_xenon0: <Armada Xenon SDHCI controller> mem 0xd0000-0xd02ff,0x1e808-0x1e80b irq 25 on simplebus1
sdhci_xenon1: <Armada Xenon SDHCI controller> mem 0xd8000-0xd82ff,0x17808-0x1780b irq 26 on simplebus1
mmc0: <MMC/SD bus> on sdhci_xenon1
ahci0: <AHCI SATA controller> mem 0xe0000-0xe0177 irq 27 on simplebus1
ahci0: AHCI v1.30 with 1 6Gbps ports, Port Multiplier supported with FBS
ahcich0: <AHCI channel> at channel 0 on ahci0
device_attach: ahcich0 attach returned 6
pcib0: <Marvell Armada 3700 PCIe Bus Controller> mem 0xd0070000-0xd008ffff irq 5 on simplebus0
pcib0: link up
pci0: <OFW PCI bus> on pcib0
pci0: failed to allocate bus number
device_attach: pci0 attach returned 6
gpioled0: <GPIO LEDs> on ofwbus0
armv8crypto0: <AES-CBC,AES-XTS,AES-GCM>
Timecounters tick every 1.000 msec
mvneta0: link state changed to UP
usbus0: 5.0Gbps Super Speed USB v3.0
usbus1: 480Mbps High Speed USB v2.0
ugen1.1: <Marvell EHCI root HUB> at usbus1
uhub0 on usbus1
uhub0: <Marvell EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1
ugen0.1: <Generic XHCI root HUB> at usbus0
uhub1 on usbus0
uhub1: <Generic XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0
ZFS filesystem version: 5
ZFS storage pool version: features support (5000)
spibus0: <OFW SPI bus> on spi0
mx25l0: <M25Pxx Flash Family> at cs 0 mode 0 on spibus0
mx25l0: device type mx25u3235f, size 4096K in 64 sectors of 64K, erase size 4K
uhub1: 2 ports with 2 removable, self powered
mmcsd0: 8GB <MMCHC SEM08G 3.10 SN B1CB28BE MFG 04/2017 by 69 0x0000> at mmc0 50.0MHz/8bit/65535-block
mmcsd0boot0: 2MB partition 1 at mmcsd0
mmcsd0boot1: 2MB partition 2 at mmcsd0
mmcsd0rpmb: 2MB partition 3 at mmcsd0
CPU  0: ARM Cortex-A53 r0p4 affinity:  0
                   Cache Type = <64 byte CWG,64 byte ERG,64 byte D-cacheline,VIPT I-cache,64 byte I-cacheline>
 Instruction Set Attributes 0 = <CRC32,SHA2,SHA1,AES+PMULL>
 Instruction Set Attributes 1 = <>
 Instruction Set Attributes 2 = <>
         Processor Features 0 = <GIC,AdvSIMD,FP,EL3 32,EL2 32,EL1 32,EL0 32>
         Processor Features 1 = <MTE_frac>
         Processor Features 2 = <>
      Memory Model Features 0 = <TGran4,TGran64,SNSMem,BigEnd,16bit ASID,1TB PA>
      Memory Model Features 1 = <8bit VMID>
      Memory Model Features 2 = <32bit CCIDX,48bit VA>
      Memory Model Features 3 = <>
      Memory Model Features 4 = <>
             Debug Features 0 = <DoubleLock,2 CTX BKPTs,4 Watchpoints,6 Breakpoints,PMUv3,Debugv8>
             Debug Features 1 = <>
         Auxiliary Features 0 = <>
         Auxiliary Features 1 = <>
AArch32 Instruction Set Attributes 5 = <CRC32,SHA2,SHA1,AES+VMULL,SEVL>
AArch32 Media and VFP Features 0 = <FPRound,FPSqrt,FPDivide,DP VFPv3+v4,SP VFPv3+v4,AdvSIMD>
AArch32 Media and VFP Features 1 = <SIMDFMAC,FPHP DP Conv,SIMDHP SP Conv,SIMDSP,SIMDInt,SIMDLS,FPDNaN,FPFtZ>
CPU  1: ARM Cortex-A53 r0p4 affinity:  1
gic0: using for IPIs
Release APs...done
Trying to mount root from zfs:pfSense/ROOT/default_20241127091912 []...
TCP_ratelimit: Is now initialized
uhub0: 1 port with 1 removable, self powered
e6000sw0port1: link state changed to DOWN
e6000sw0port2: link state changed to DOWN
e6000sw0port3: link state changed to DOWN
Warning: no time-of-day clock registered, system time will not be set accurately
Dual Console: Serial Primary, Video Secondary
e6000sw0port2: link state changed to UP
e6000sw0port3: link state changed to UP
Configuring crash dumps...
No suitable dump device was found.
Filesystems are clean, continuing...
Mounting filesystems...
Mounting ZFS boot environment...done.
Current time is older than key file time, using file time instead.

        __
 _ __  / _|___  ___ _ __  ___  ___      _
| '_ \| |_/ __|/ _ \ '_ \/ __|/ _ \   _| |_
| |_) |  _\__ \  __/ | | \__ \  __/  |_   _|
| .__/|_| |___/\___|_| |_|___/\___|    |_|
|_|


Welcome to Netgate pfSense Plus 25.11-RELEASE...

...ELF ldconfig path: /lib /usr/lib /usr/lib/compat /usr/local/lib /usr/local/lib/compat/pkg /usr/local/lib/compat/pkg /usr/local/lib/ipsec /usr/local/lib/perl5/5.42/mach/CORE
32-bit compatibility ldconfig path:
done.
External config loader 1.0 is now starting... mmcsd0p1 mmcsd0p2 mmcsd0p3
Launching the init system... done.
Initializing.................... done.
Starting device manager (devd)...done.
Loading configuration...2025-12-30T15:12:19.481490-06:00 - php-fpm 596 - - /rc.linkup: Ignoring link event during boot sequence.
2025-12-30T15:12:19.509141-06:00 - php-fpm 596 - - /rc.linkup: Ignoring link event during boot sequence.
2025-12-30T15:12:19.525923-06:00 - php-fpm 597 - - /rc.linkup: Ignoring link event during boot sequence.
2025-12-30T15:12:19.535008-06:00 - php-fpm 596 - - /rc.linkup: Ignoring link event during boot sequence.
2025-12-30T15:12:19.561453-06:00 - php-fpm 597 - - /rc.linkup: Ignoring link event during boot sequence.
done.
Updating configuration...2025-12-30T15:12:19.641773-06:00 - php-fpm 1837 - - /rc.linkup: Ignoring link event during boot sequence.
.done.
Checking config backups consistency...done.
Loading cryptographic accelerator drivers...done.
Setting up extended sysctls...done.
Executing deferred package installation scripts...Running last steps of FTP_Client_Proxy installation.
Saving updated package information...
overwrite!
Loading package configuration... done.
Configuring package components...
Loading package instructions...
Custom commands...
Executing custom_php_resync_config_command()...done.
Menu items... done.
Services... done.
Writing configuration... done.
Running last steps of Nexus installation.
Saving updated package information...
overwrite!
Loading package configuration... done.
Configuring package components...
Custom commands...
Writing configuration... done.
Running last steps of nmap installation.
Saving updated package information...
overwrite!
Loading package configuration... done.
Configuring package components...
Custom commands...
Menu items... done.
Writing configuration... done.
done.
Executing early shell commands...done.
Setting timezone...done.
Configuring loopback interface...done.
Starting syslog...done.
Configuring switch...e6000sw0port2: link state changed to DOWN
e6000sw0port3: link state changed to DOWN
done.
Setting up interfaces microcode...done.
Configuring loopback interface...done.
Creating wireless clone interfaces...done.
Configuring VLAN interfaces...vlan0: changing name to 'mvneta0.4090'
2025-12-30T15:12:35.915865-06:00 SG1100.pfsense.local php-fpm 596 - - /rc.linkup: Ignoring link event during boot sequence.
2025-12-30T15:12:35.940478-06:00 SG1100.pfsense.local php-fpm 597 - - /rc.linkup: Ignoring link event during boot sequence.
e6000sw0port2: link state changed to UP
e6000sw0port3: link state changed to UP
2025-12-30T15:12:39.289296-06:00 SG1100.pfsense.local php-fpm 597 - - /rc.linkup: Ignoring link event during boot sequence.
2025-12-30T15:12:40.314739-06:00 SG1100.pfsense.local php-fpm 597 - - /rc.linkup: Ignoring link event during boot sequence.
vlan1: changing name to 'mvneta0.4091'
vlan2: changing name to 'mvneta0.4092'
done.
Configuring WAN interface...2025-12-30T15:12:44.216567-06:00 SG1100.pfsense.local php-fpm 597 - - /rc.newwanip: rc.newwanip: Info: starting on mvneta0.4090.
2025-12-30T15:12:44.218709-06:00 SG1100.pfsense.local php-fpm 597 - - /rc.newwanip: rc.newwanip: on (IP address: 192.168.1.76) (interface: WAN[wan]) (real interface: mvneta0.4090).
pflog0: promiscuous mode enabled
done.
Configuring LAN interface...done.
Configuring LAN2 interface...done.
Configuring WIRELESS interface...ifconfig: interface ath0_wlan0 does not exist
2025-12-30T15:12:46.133462-06:00 SG1100.pfsense.local php-fpm 596 - - /rc.newwanip: rc.newwanip: Info: starting on mvneta0.4090.
2025-12-30T15:12:46.135520-06:00 SG1100.pfsense.local php-fpm 596 - - /rc.newwanip: rc.newwanip: on (IP address: 192.168.1.76) (interface: WAN[wan]) (real interface: mvneta0.4090).
done.
bridge0: Ethernet address: 58:9c:fc:10:c6:bb
bridge0: WARNING: Adding member interface mvneta0.4091 which has an IP address assigned is deprecated and will be unsupported in a future release.
bridge0: link state changed to UP
mvneta0: promiscuous mode enabled
mvneta0.4091: promiscuous mode enabled
bridge0: WARNING: Adding member interface mvneta0.4092 which has an IP address assigned is deprecated and will be unsupported in a future release.
mvneta0.4092: promiscuous mode enabled
Configuring BRIDGE interface...done.
Configuring CARP settings...done.
Syncing OpenVPN settings...2025-12-30T15:12:47.198435-06:00 SG1100.pfsense.local php-fpm 596 - - /rc.newwanip: Default gateway setting Interface WAN_DHCP Gateway as default.
done.
route: route has not been found
route: route has not been found
Configuring firewall.....ovpn0: changing name to 'ovpnc1'
ovpnc1: link state changed to UP
.done.
Starting PFLOG...done.
Setting up gateway monitors...done.
Setting up static routes...done.
Setting up DNSs...
2025-12-30T15:12:48.727607-06:00 SG1100.pfsense.local php-fpm 1837 - - /rc.newwanip: rc.newwanip: Info: starting on ovpnc1.
2025-12-30T15:12:48.732177-06:00 SG1100.pfsense.local php-fpm 1837 - - /rc.newwanip: rc.newwanip: on (IP address: 192.168.236.2) (interface: S2SOVPN[opt2]) (real interface: ovpnc1).
Starting DNS Resolver...done.
Synchronizing user settings...done.
Configuring CRON...done.
Bootstrapping clock...done.
Starting NTP Server...done.
Starting webConfigurator...done.
Starting DHCP service...done.
Configuring firewall......done.
Generating RRD graphs...done.
Starting syslog...done.
Starting CRON... done.
 Starting package nmap...done.
 Starting package FTP Client Proxy...done.
 Starting package Netgate Nexus...done.
Netgate pfSense Plus 25.11-RELEASE arm64 20251215-1821
Bootup complete
Performing automatic boot verification...done.