---<<BOOT>>---
APIC: Using the MADT enumerator.
Copyright (c) 1992-2021 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 12.2-STABLE plus-devel-12-n202537-38f644d767c pfSense amd64
FreeBSD clang version 10.0.1 (git@github.com:llvm/llvm-project.git llvmorg-10.0.1-0-gef32c611aa2)
PPIM 0: PA=0xa0000, VA=0xffffffff84310000, size=0x10000, mode=0
pmap: large map 8 PML4 slots (4096 Gb)
VT(vga): resolution 640x480
Preloaded elf kernel "/boot/kernel/kernel" at 0xffffffff840b5000.
Preloaded elf obj module "/boot/kernel/zfs.ko" at 0xffffffff840be1d0.
Preloaded elf obj module "/boot/kernel/opensolaris.ko" at 0xffffffff840beab8.
Preloaded boot_entropy_cache "/boot/entropy" at 0xffffffff840bf168.
Calibrating TSC clock ... TSC clock: 2200071210 Hz
CPU: Intel(R) Atom(TM) CPU C3558 @ 2.20GHz (2200.07-MHz K8-class CPU)
  Origin="GenuineIntel"  Id=0x506f1  Family=0x6  Model=0x5f  Stepping=1
  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Features2=0x4ff8ebbf<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,SDBG,CX16,xTPR,PDCM,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,TSCDLT,AESNI,XSAVE,OSXSAVE,RDRAND>
  AMD Features=0x2c100800<SYSCALL,NX,Page1GB,RDTSCP,LM>
  AMD Features2=0x101<LAHF,Prefetch>
  Structured Extended Features=0x2294e283<FSGSBASE,TSCADJ,SMEP,ERMS,NFPUSG,MPX,PQE,RDSEED,SMAP,CLFLUSHOPT,PROCTRACE,SHA>
  Structured Extended Features3=0x2c000000<IBPB,STIBP,ARCH_CAP>
  XSAVE Features=0xf<XSAVEOPT,XSAVEC,XINUSE,XSAVES>
  IA32_ARCH_CAPS=0x1<RDCL_NO>
  VT-x: Basic Features=0xda0400<SMM,INS/OUTS,TRUE>
        Pin-Based Controls=0xff<ExtINT,NMI,VNMI,PreTmr,PostIntr>
        Primary Processor Controls=0xfff9fffe<INTWIN,TSCOff,HLT,INVLPG,MWAIT,RDPMC,RDTSC,CR3-LD,CR3-ST,CR8-LD,CR8-ST,TPR,NMIWIN,MOV-DR,IO,IOmap,MTF,MSRmap,MONITOR,PAUSE>
        Secondary Processor Controls=0x1d6fff<APIC,EPT,DT,RDTSCP,x2APIC,VPID,WBINVD,UG,APIC-reg,VID,PAUSE-loop,RDRAND,VMFUNC,VMCS,XSAVES>
        Exit Controls=0xda0400<PAT-LD,EFER-SV,PTMR-SV>
        Entry Controls=0xda0400
        EPT Features=0x6334141<XO,PW4,UC,WB,2M,1G,INVEPT,AD,single,all>
        VPID Features=0xf01<INVVPID,individual,single,all,single-globals>
  TSC: P-state invariant, performance statistics
DTLB: 4k pages, fully associative, 32 entries
Data TLB: 4 KBytes pages, 4-way set associative, 512 entries
Instruction TLB: 4 KByte pages, fully associative, 48 entries
DTLB: 2M/4M Byte pages, 4-way associative, 32 entries
L2 cache: 2048 kbytes, 16-way associative, 64 bytes/line
real memory  = 10737418240 (10240 MB)
Physical memory chunk(s):
0x0000000000010000 - 0x000000000009efff, 585728 bytes (143 pages)
0x0000000000103000 - 0x00000000001fffff, 1036288 bytes (253 pages)
0x0000000004300000 - 0x000000007f6c3fff, 2067546112 bytes (504772 pages)
0x0000000100000000 - 0x0000000270140fff, 6175330304 bytes (1507649 pages)
avail memory = 8209952768 (7829 MB)
MADT: Found CPU APIC ID 0 ACPI ID 0: enabled
SMP: Added CPU 0 (AP)
MADT: Found CPU APIC ID 8 ACPI ID 1: enabled
SMP: Added CPU 8 (AP)
MADT: Found CPU APIC ID 28 ACPI ID 2: enabled
SMP: Added CPU 28 (AP)
MADT: Found CPU APIC ID 20 ACPI ID 3: enabled
SMP: Added CPU 20 (AP)
Event timer "LAPIC" quality 600
ACPI APIC Table: <CORE   COREBOOT>
WARNING: L1 data cache covers fewer APIC IDs than a core (0 < 1)
Package ID shift: 5
L2 cache ID shift: 2
L1 cache ID shift: 1
Core ID shift: 1
INTR: Adding local APIC 8 as a target
INTR: Adding local APIC 20 as a target
INTR: Adding local APIC 28 as a target
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
FreeBSD/SMP: 1 package(s) x 4 core(s)
Package HW ID = 0
	Core HW ID = 0
		CPU0 (BSP): APIC ID: 0
	Core HW ID = 4
		CPU1 (AP): APIC ID: 8
	Core HW ID = 10
		CPU2 (AP): APIC ID: 20
	Core HW ID = 14
		CPU3 (AP): APIC ID: 28
APIC: CPU 0 has ACPI ID 0
APIC: CPU 1 has ACPI ID 1
APIC: CPU 2 has ACPI ID 3
APIC: CPU 3 has ACPI ID 2
lapic0: CMCI unmasked
Pentium Pro MTRR support enabled
x86bios:  IVT 0x000000-0x0004ff at 0xfffff80000000000
x86bios: SSEG 0x09e000-0x09efff at 0xfffffe00025f5000
x86bios: EBDA 0x09f000-0x09ffff at 0xfffff8000009f000
x86bios:  ROM 0x0a0000-0x0fefff at 0xfffff800000a0000
random: read 3840 bytes from preloaded cache
random: unblocking device.
arc4random: read 32 bytes from preloaded cache
arc4random: read 32 bytes from preloaded cache
arc4random: read 32 bytes from preloaded cache
arc4random: read 32 bytes from preloaded cache
VIMAGE (virtualized network stack) enabled
hostuuid: using 00000000-0000-0000-0000-000000000000
ULE: setup cpu 0
ULE: setup cpu 1
ULE: setup cpu 2
ULE: setup cpu 3
ACPI: RSDP 0x00000000000F56D0 000024 (v02 CORE  )
ACPI: XSDT 0x000000007F6E80E0 000054 (v01 CORE   COREBOOT 00000000 CORE 00000000)
ACPI: FACP 0x000000007F6EA280 0000F4 (v03 CORE   COREBOOT 00000000 CORE 00000001)
ACPI: DSDT 0x000000007F6E8280 001FFE (v02 COREv4 COREBOOT 20110725 INTL 20161222)
ACPI: FACS 0x000000007F6E8240 000040
ACPI: SSDT 0x000000007F6EA380 000C34 (v02 CORE   COREBOOT 0000002A CORE 0000002A)
ACPI: MCFG 0x000000007F6EAFC0 00003C (v01 CORE   COREBOOT 00000000 CORE 00000000)
ACPI: TCPA 0x000000007F6EB000 000032 (v02 CORE   COREBOOT 00000000 CORE 00000000)
ACPI: APIC 0x000000007F6EB040 00006C (v01 CORE   COREBOOT 00000000 CORE 00000000)
ACPI: DMAR 0x000000007F6EB0B0 000088 (v01 CORE   COREBOOT 00000000 CORE 00000000)
MADT: Found IO APIC ID 2, Interrupt 0 at 0xfec00000
ioapic0: MADT APIC ID 2 != hw id 1
ioapic0: ver 0x20 maxredir 0x17
ioapic0: Routing external 8259A's -> intpin 0
MADT: Interrupt override: source 0, irq 2
ioapic0: Routing IRQ 0 -> intpin 2
MADT: Interrupt override: source 9, irq 9
ioapic0: intpin 9 trigger: level
ioapic0 <Version 2.0> irqs 0-23 on motherboard
lapic: Divisor 2, Frequency 12500407 Hz
lapic: deadline tsc mode, Frequency 2200071210 Hz
cpu0 BSP:
     ID: 0x00000000   VER: 0x01060014 LDR: 0x00000001 DFR: 0x00000000 x2APIC: 1
  lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000011ff
  timer: 0x000100ef therm: 0x00010000 err: 0x000000f0 pmc: 0x00010400
   cmci: 0x000000f2
lapic28: CMCI unmasked
SMP: AP CPU #3 Launched!
cpu3 AP:
     ID: 0x0000001c   VER: 0x01060014 LDR: 0x00011000 DFR: 0x00000000 x2APIC: 1
  lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000011ff
  timer: 0x000100ef therm: 0x00010000 err: 0x000000f0 pmc: 0x00010400
   cmci: 0x000000f2
lapic8: CMCI unmasked
SMP: AP CPU #1 Launched!
cpu1 AP:
     ID: 0x00000008   VER: 0x01060014 LDR: 0x00000100 DFR: 0x00000000 x2APIC: 1
  lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000011ff
  timer: 0x000100ef therm: 0x00010000 err: 0x000000f0 pmc: 0x00010400
   cmci: 0x000000f2
lapic20: CMCI unmasked
SMP: AP CPU #2 Launched!
cpu2 AP:
     ID: 0x00000014   VER: 0x01060014 LDR: 0x00010010 DFR: 0x00000000 x2APIC: 1
  lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000011ff
  timer: 0x000100ef therm: 0x00010000 err: 0x000000f0 pmc: 0x00010400
   cmci: 0x000000f2
SMP: passed TSC synchronization test
TSC timecounter discards lower 1 bit(s)
Timecounter "TSC-low" frequency 1100035605 Hz quality 1000
random: entropy device external interface
firmware: 'iwn135fw' version 0: 701228 bytes loaded at 0xffffffff82c2ec70
firmware: 'iwn2000fw' version 0: 695876 bytes loaded at 0xffffffff82cda050
firmware: 'iwn2030fw' version 0: 707392 bytes loaded at 0xffffffff82d83f48
wlan: <802.11 Link Layer>
firmware: 'iwn4965fw' version 0: 187972 bytes loaded at 0xffffffff82e30b38
firmware: 'mw88W8363fw' version 0: 94940 bytes loaded at 0xffffffff83139e98
firmware: 'mwlboot' version 0: 2280 bytes loaded at 0xffffffff83151178
firmware: 'rtwn-rtl8188eefw' version 111: 11216 bytes loaded at 0xffffffff831e8188
firmware: 'rtwn-rtl8188eufw' version 111: 13904 bytes loaded at 0xffffffff831eae08
firmware: 'rtwn-rtl8192cfwE' version 111: 14818 bytes loaded at 0xffffffff831ee508
firmware: 'wpifw' version 153229: 150100 bytes loaded at 0xffffffff832a13d8
firmware: 'rtwn-rtl8192cfwE_B' version 111: 16332 bytes loaded at 0xffffffff831f1fa0
firmware: 'rtwn-rtl8192cfwT' version 111: 16126 bytes loaded at 0xffffffff831f6020
firmware: 'rtwn-rtl8192cfwU' version 111: 16126 bytes loaded at 0xffffffff831f9fd0
firmware: 'rtwn-rtl8192eufw' version 111: 31818 bytes loaded at 0xffffffff831fdf80
firmware: 'rtwn-rtl8812aufw' version 111: 32060 bytes loaded at 0xffffffff83205c80
firmware: 'rtwn-rtl8821aufw' version 111: 27804 bytes loaded at 0xffffffff8320da70
firmware: 'mxge_eth_z8e' version 377284: 120629 bytes loaded at 0xffffffff83151c40
firmware: 'mxge_ethp_z8e' version 387604: 121317 bytes loaded at 0xffffffff8316f430
firmware: 'mxge_rss_eth_z8e' version 534724: 151912 bytes loaded at 0xffffffff8318ced0
firmware: 'mxge_rss_ethp_z8e' version 544468: 152837 bytes loaded at 0xffffffff831b20f0
firmware: 'iwn5000fw' version 0: 340696 bytes loaded at 0xffffffff82e5ea30
firmware: 'iwn5150fw' version 0: 337400 bytes loaded at 0xffffffff82eb1db8
firmware: 'iwn6000fw' version 0: 454608 bytes loaded at 0xffffffff82f04460
firmware: 'iwn6000g2afw' version 0: 677296 bytes loaded at 0xffffffff82f734e0
snd_unit_init() u=0x00ff8000 [512] d=0x00007c00 [32] c=0x000003ff [1024]
feeder_register: snd_unit=-1 snd_maxautovchans=16 latency=2 feeder_rate_min=1 feeder_rate_max=2016000 feeder_rate_round=25
firmware: 'iwn6000g2bfw' version 0: 679436 bytes loaded at 0xffffffff83018b40
firmware: 'iwn6050fw' version 0: 469780 bytes loaded at 0xffffffff830bea00
firmware: 't6fw_cfg' version 0: 5957 bytes loaded at 0xffffffff81fba9d0
firmware: 't6fw_cfg_uwire' version 0: 22705 bytes loaded at 0xffffffff81fbc118
firmware: 't6fw' version 0: 731648 bytes loaded at 0xffffffff81fc19d0
ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE.
ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_bss_fw, 0xffffffff8073c810, 0) error 1
ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE.
ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_ibss_fw, 0xffffffff8073c8c0, 0) error 1
ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE.
ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_monitor_fw, 0xffffffff8073c970, 0) error 1
iwi_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE.
iwi_bss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_bss_fw, 0xffffffff80764200, 0) error 1
iwi_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE.
iwi_ibss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_ibss_fw, 0xffffffff807642b0, 0) error 1
iwi_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE.
iwi_monitor: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_monitor_fw, 0xffffffff80764360, 0) error 1
firmware: 't4fw_cfg' version 0: 4535 bytes loaded at 0xffffffff81e7dc60
firmware: 't4fw_cfg_uwire' version 0: 21445 bytes loaded at 0xffffffff81e7ee18
firmware: 't4fw' version 0: 569856 bytes loaded at 0xffffffff81e841e0
firmware: 't5fw_cfg' version 0: 5914 bytes loaded at 0xffffffff81f0f490
firmware: 't5fw_cfg_uwire' version 0: 21871 bytes loaded at 0xffffffff81f10bb0
firmware: 't5fw' version 0: 673792 bytes loaded at 0xffffffff81f16120
firmware: 'iwm3160fw' version 0: 918268 bytes loaded at 0xffffffff8219b2a0
firmware: 'iwm3168fw' version 0: 1028032 bytes loaded at 0xffffffff8227b650
firmware: 'iwm7260fw' version 0: 1049340 bytes loaded at 0xffffffff823766c0
firmware: 'iwm7265fw' version 0: 1180412 bytes loaded at 0xffffffff82476a70
firmware: 'rsu-rtl8712fw' version 120: 122328 bytes loaded at 0xffffffff8326b1a8
firmware: 'runfw' version 0: 8192 bytes loaded at 0xffffffff83289390
firmware: 'iwm7265Dfw' version 0: 1383604 bytes loaded at 0xffffffff82596e20
firmware: 'iwm8000Cfw' version 0: 2351636 bytes loaded at 0xffffffff826e8b88
firmware: 'rt2561fw' version 0: 8192 bytes loaded at 0xffffffff831deed0
firmware: 'rt2561sfw' version 0: 8192 bytes loaded at 0xffffffff831e0f80
firmware: 'rt2661fw' version 0: 8192 bytes loaded at 0xffffffff831e3030
firmware: 'rt2860fw' version 0: 8192 bytes loaded at 0xffffffff831e50e0
firmware: 'iwm8265fw' version 0: 1811984 bytes loaded at 0xffffffff82926e50
wlan: mac acl policy registered
firmware: 'iwn1000fw' version 0: 337520 bytes loaded at 0xffffffff82ae1738
firmware: 'iwn100fw' version 0: 337572 bytes loaded at 0xffffffff82b33e58
firmware: 'iwn105fw' version 0: 689680 bytes loaded at 0xffffffff82b865b0
WARNING: Device "g_ctl" is Giant locked and may be deleted before FreeBSD 14.0.
EFI systbl not available
null: <full device, null device, zero device>
WARNING: Device "pci" is Giant locked and may be deleted before FreeBSD 14.0.
nfslock: pseudo-device
tcp_log: tcp_log device
crypto: <crypto core>
module_register_init: MOD_LOAD (vesa, 0xffffffff814060c0, 0) error 19
io: <I/O>
WARNING: Device "kbd" is Giant locked and may be deleted before FreeBSD 14.0.
kbd0 at kbdmux0
random: registering fast source Intel Secure Key RNG
random: fast provider: "Intel Secure Key RNG"
WARNING: Device "spkr" is Giant locked and may be deleted before FreeBSD 14.0.
[ath_hal] loaded
mem: <memory>
000.000059 [4344] netmap_init               netmap: loaded module
mlx5en: Mellanox Ethernet driver 3.6.0 (December 2020)
hptnr: R750/DC7280 controller driver v1.1.5
hptrr: RocketRAID 17xx/2xxx SATA controller driver v1.2
hpt27xx: RocketRAID 27xx controller driver v1.2.8
nexus0
vtvga0: <VT VGA driver> on motherboard
cryptosoft0: <software crypto> on motherboard
crypto: assign cryptosoft0 driver id 0, flags 0x6000000
crypto: cryptosoft0 registers alg 1 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 2 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 3 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 4 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 5 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 16 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 6 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 7 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 32 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 18 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 19 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 20 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 8 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 15 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 9 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 10 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 13 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 14 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 34 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 35 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 36 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 37 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 11 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 22 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 23 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 25 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 24 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 26 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 27 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 28 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 21 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 17 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 29 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 30 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 31 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 40 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 39 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 38 flags 0 maxoplen 0
acpi0: <CORE COREBOOT> on motherboard
ACPI: 2 ACPI AML tables successfully acquired and loaded
PCIe: Memory Mapped configuration base @ 0xe0000000
ioapic0: routing intpin 9 (ISA IRQ 9) to lapic 0 vector 48
acpi0: Power Button (fixed)
acpi0: wakeup code va 0xfffffe00003ff000 pa 0x9c000
hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
hpet0: vendor 0x8086, rev 0x1, 24000000Hz 64bit, 8 timers, legacy route
hpet0:  t0: irqs 0x00f00000 (0), MSI, 64bit, periodic
hpet0:  t1: irqs 0x00f00000 (0), MSI
hpet0:  t2: irqs 0x00f00800 (0), MSI
hpet0:  t3: irqs 0x00f01000 (0), MSI
hpet0:  t4: irqs 0x00000000 (0), MSI
hpet0:  t5: irqs 0x00000000 (0), MSI
hpet0:  t6: irqs 0x00000000 (0), MSI
hpet0:  t7: irqs 0x00000000 (0), MSI
Timecounter "HPET" frequency 24000000 Hz quality 950
msi: routing MSI-X IRQ 256 to local APIC 8 vector 48
msi: routing MSI-X IRQ 257 to local APIC 20 vector 48
msi: routing MSI-X IRQ 258 to local APIC 28 vector 48
msi: routing MSI-X IRQ 259 to local APIC 0 vector 49
msi: routing MSI-X IRQ 260 to local APIC 8 vector 49
msi: routing MSI-X IRQ 261 to local APIC 20 vector 49
msi: routing MSI-X IRQ 262 to local APIC 28 vector 49
msi: routing MSI-X IRQ 263 to local APIC 0 vector 50
msi: Assigning MSI-X IRQ 256 to local APIC 0 vector 51
msi: Assigning MSI-X IRQ 257 to local APIC 8 vector 48
msi: Assigning MSI-X IRQ 258 to local APIC 20 vector 48
msi: Assigning MSI-X IRQ 259 to local APIC 28 vector 48
msi: Assigning MSI-X IRQ 260 to local APIC 0 vector 49
msi: Assigning MSI-X IRQ 261 to local APIC 0 vector 52
msi: Assigning MSI-X IRQ 262 to local APIC 0 vector 53
Event timer "HPET" frequency 24000000 Hz quality 550
Event timer "HPET1" frequency 24000000 Hz quality 440
Event timer "HPET2" frequency 24000000 Hz quality 440
Event timer "HPET3" frequency 24000000 Hz quality 440
Event timer "HPET4" frequency 24000000 Hz quality 440
cpu0: Processor \_PR_.CP00 (ACPI ID 0) -> APIC ID 0
cpu0: <ACPI CPU> on acpi0
cpu1: Processor \_PR_.CP01 (ACPI ID 1) -> APIC ID 1
cpu1: <ACPI CPU> on acpi0
cpu2: Processor \_PR_.CP02 (ACPI ID 2) -> APIC ID 3
cpu2: <ACPI CPU> on acpi0
cpu3: Processor \_PR_.CP03 (ACPI ID 3) -> APIC ID 2
cpu3: <ACPI CPU> on acpi0
atrtc0: <AT realtime clock> port 0x70-0x77 on acpi0
atrtc0: Warning: Couldn't map I/O.
atrtc0: registered as a time-of-day clock, resolution 1.000000s
ioapic0: routing intpin 8 (ISA IRQ 8) to lapic 8 vector 49
ioapic0: routing intpin 8 (ISA IRQ 8) to lapic 0 vector 54
Event timer "RTC" frequency 32768 Hz quality 0
attimer0: <AT timer> port 0x40-0x43,0x50-0x53 irq 0 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
ioapic0: routing intpin 2 (ISA IRQ 0) to lapic 20 vector 49
Event timer "i8254" frequency 1193182 Hz quality 100
ACPI timer: 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 -> 10
Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1808-0x180b on acpi0
pci_link0:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0   11   N     0  3 4 6 10 11 12 14 15
  Validation          0   11   N     0  3 4 6 10 11 12 14 15
  After Disable       0  255   N     0  3 4 6 10 11 12 14 15
pci_link1:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0   10   N     0  3 4 6 10 11 12 14 15
  Validation          0   10   N     0  3 4 6 10 11 12 14 15
  After Disable       0  255   N     0  3 4 6 10 11 12 14 15
pci_link2:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0    3   N     0  3
  Validation          0    3   N     0  3
  After Disable       0  255   N     0  3
pci_link3:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0    4   N     0  4
  Validation          0    4   N     0  4
  After Disable       0  255   N     0  4
pci_link4:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0   12   N     0  3 4 6 10 11 12 14 15
  Validation          0   12   N     0  3 4 6 10 11 12 14 15
  After Disable       0  255   N     0  3 4 6 10 11 12 14 15
pci_link5:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0   14   N     0  3 4 6 10 11 12 14 15
  Validation          0   14   N     0  3 4 6 10 11 12 14 15
  After Disable       0  255   N     0  3 4 6 10 11 12 14 15
pci_link6:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0   15   N     0  3 4 6 10 11 12 14 15
  Validation          0   15   N     0  3 4 6 10 11 12 14 15
  After Disable       0  255   N     0  3 4 6 10 11 12 14 15
pci_link7:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0    6   N     0  3 4 6 10 11 12 14 15
  Validation          0    6   N     0  3 4 6 10 11 12 14 15
  After Disable       0  255   N     0  3 4 6 10 11 12 14 15
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pcib0: decoding 5 range 0-0xff
pcib0: decoding 4 range 0-0xcf7
pcib0: decoding 4 range 0xd00-0xffff
pcib0: decoding 3 range 0xa0000-0xbffff
pcib0: decoding 3 range 0xc0000-0xdffff
pcib0: decoding 3 range 0x80000000-0xdfffffff
pcib0: decoding 3 range 0x280000000-0xfffffffff
pci0: <ACPI PCI bus> on pcib0
pci0: domain=0, physical bus=0
found->	vendor=0x8086, dev=0x1980, revid=0x11
	domain=0, bus=0, slot=0, func=0
	class=06-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0007, statreg=0x0000, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x8086, dev=0x19a1, revid=0x11
	domain=0, bus=0, slot=4, func=0
	class=06-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0000, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x8086, dev=0x19a2, revid=0x11
	domain=0, bus=0, slot=5, func=0
	class=08-07-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0004, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=11
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message, vector masks
pcib0: matched entry for 0.5.INTA
pcib0: slot 5 INTA hardwired to IRQ 23
found->	vendor=0x8086, dev=0x19a3, revid=0x11
	domain=0, bus=0, slot=6, func=0
	class=06-04-00, hdrtype=0x01, mfdev=0
	cmdreg=0x0006, statreg=0x0010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=11
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message, vector masks
pcib0: matched entry for 0.6.INTA
pcib0: slot 6 INTA hardwired to IRQ 18
	secbus=1, subbus=1
found->	vendor=0x8086, dev=0x19a8, revid=0x11
	domain=0, bus=0, slot=14, func=0
	class=06-04-00, hdrtype=0x01, mfdev=0
	cmdreg=0x0002, statreg=0x0010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=11
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message, vector masks
	map[10]: type Memory, range 64, base 0xdfe00000, size 17, enabled
pcib0: allocated type 3 (0xdfe00000-0xdfe1ffff) for rid 10 of pci0:0:14:0
pcib0: matched entry for 0.14.INTA
pcib0: slot 14 INTA hardwired to IRQ 20
	secbus=2, subbus=2
found->	vendor=0x8086, dev=0x19aa, revid=0x11
	domain=0, bus=0, slot=16, func=0
	class=06-04-00, hdrtype=0x01, mfdev=0
	cmdreg=0x0002, statreg=0x0010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=c, irq=3
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message, vector masks
	map[10]: type Memory, range 64, base 0xdfe20000, size 17, enabled
pcib0: allocated type 3 (0xdfe20000-0xdfe3ffff) for rid 10 of pci0:0:16:0
pcib0: matched entry for 0.16.INTC
pcib0: slot 16 INTC hardwired to IRQ 22
	secbus=3, subbus=3
found->	vendor=0x8086, dev=0x19ab, revid=0x11
	domain=0, bus=0, slot=17, func=0
	class=06-04-00, hdrtype=0x01, mfdev=0
	cmdreg=0x0002, statreg=0x0010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=d, irq=4
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message, vector masks
	map[10]: type Memory, range 64, base 0xdfe40000, size 17, enabled
pcib0: allocated type 3 (0xdfe40000-0xdfe5ffff) for rid 10 of pci0:0:17:0
pcib0: matched entry for 0.17.INTD
pcib0: slot 17 INTD hardwired to IRQ 23
	secbus=4, subbus=4
found->	vendor=0x8086, dev=0x19ac, revid=0x11
	domain=0, bus=0, slot=18, func=0
	class=08-80-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0006, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=11
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message, 64 bit, vector masks
	map[10]: type Memory, range 64, base 0xdfe7b000, size 10, enabled
pcib0: allocated type 3 (0xdfe7b000-0xdfe7b3ff) for rid 10 of pci0:0:18:0
pcib0: matched entry for 0.18.INTA
pcib0: slot 18 INTA hardwired to IRQ 16
found->	vendor=0x8086, dev=0x19c2, revid=0x11
	domain=0, bus=0, slot=20, func=0
	class=01-06-01, hdrtype=0x00, mfdev=0
	cmdreg=0x0007, statreg=0x02b0, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=11
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message
	MSI-X supports 8 messages in maps 0x10 and 0x14
	map[10]: type Memory, range 32, base 0xdfe74000, size 13, enabled
pcib0: allocated type 3 (0xdfe74000-0xdfe75fff) for rid 10 of pci0:0:20:0
	map[14]: type Memory, range 32, base 0xdfe7c000, size  8, enabled
pcib0: allocated type 3 (0xdfe7c000-0xdfe7c0ff) for rid 14 of pci0:0:20:0
	map[18]: type I/O Port, range 32, base 0x1c20, size  3, enabled
pcib0: allocated type 4 (0x1c20-0x1c27) for rid 18 of pci0:0:20:0
	map[1c]: type I/O Port, range 32, base 0x1c28, size  2, enabled
pcib0: allocated type 4 (0x1c28-0x1c2b) for rid 1c of pci0:0:20:0
	map[20]: type I/O Port, range 32, base 0x1c00, size  5, enabled
pcib0: allocated type 4 (0x1c00-0x1c1f) for rid 20 of pci0:0:20:0
	map[24]: type Memory, range 32, base 0xdfe7a000, size 11, enabled
pcib0: allocated type 3 (0xdfe7a000-0xdfe7a7ff) for rid 24 of pci0:0:20:0
pcib0: matched entry for 0.20.INTA
pcib0: slot 20 INTA hardwired to IRQ 21
found->	vendor=0x8086, dev=0x19d0, revid=0x11
	domain=0, bus=0, slot=21, func=0
	class=0c-03-30, hdrtype=0x00, mfdev=0
	cmdreg=0x0006, statreg=0x0290, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=11
	powerspec 2  supports D0 D3  current D0
	MSI supports 8 messages, 64 bit
	map[10]: type Memory, range 64, base 0xdfe60000, size 16, enabled
pcib0: allocated type 3 (0xdfe60000-0xdfe6ffff) for rid 10 of pci0:0:21:0
pcib0: matched entry for 0.21.INTA
pcib0: slot 21 INTA hardwired to IRQ 19
found->	vendor=0x8086, dev=0x19d1, revid=0x11
	domain=0, bus=0, slot=22, func=0
	class=06-04-00, hdrtype=0x01, mfdev=0
	cmdreg=0x0006, statreg=0x0010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=11
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message, vector masks
pcib0: matched entry for 0.22.INTA
pcib0: slot 22 INTA hardwired to IRQ 16
	secbus=5, subbus=5
found->	vendor=0x8086, dev=0x19d2, revid=0x11
	domain=0, bus=0, slot=23, func=0
	class=06-04-00, hdrtype=0x01, mfdev=0
	cmdreg=0x0006, statreg=0x0010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=11
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message, vector masks
pcib0: matched entry for 0.23.INTA
pcib0: slot 23 INTA hardwired to IRQ 17
	secbus=6, subbus=6
found->	vendor=0x8086, dev=0x19d3, revid=0x11
	domain=0, bus=0, slot=24, func=0
	class=07-80-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0006, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=11
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message, 64 bit
	map[10]: type Memory, range 64, base 0xdfe76000, size 12, enabled
pcib0: allocated type 3 (0xdfe76000-0xdfe76fff) for rid 10 of pci0:0:24:0
pcib0: matched entry for 0.24.INTA
pcib0: slot 24 INTA hardwired to IRQ 16
found->	vendor=0x8086, dev=0x19db, revid=0x11
	domain=0, bus=0, slot=28, func=0
	class=08-05-01, hdrtype=0x00, mfdev=0
	cmdreg=0x0006, statreg=0x0010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=11
	powerspec 3  supports D0 D3  current D0
	map[10]: type Memory, range 64, base 0xdfe77000, size 12, enabled
pcib0: allocated type 3 (0xdfe77000-0xdfe77fff) for rid 10 of pci0:0:28:0
	map[18]: type Memory, range 64, base 0xdfe78000, size 12, enabled
pcib0: allocated type 3 (0xdfe78000-0xdfe78fff) for rid 18 of pci0:0:28:0
pcib0: matched entry for 0.28.INTA
pcib0: slot 28 INTA hardwired to IRQ 16
found->	vendor=0x8086, dev=0x19dc, revid=0x11
	domain=0, bus=0, slot=31, func=0
	class=06-01-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0007, statreg=0x0200, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x8086, dev=0x19de, revid=0x11
	domain=0, bus=0, slot=31, func=2
	class=05-80-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0006, statreg=0x0000, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	map[10]: type Memory, range 32, base 0xdfe70000, size 14, enabled
pcib0: allocated type 3 (0xdfe70000-0xdfe73fff) for rid 10 of pci0:0:31:2
found->	vendor=0x8086, dev=0x19df, revid=0x11
	domain=0, bus=0, slot=31, func=4
	class=0c-05-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0003, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=11
	map[10]: type Memory, range 64, base 0xdfe80000, size  8, enabled
pcib0: allocated type 3 (0xdfe80000-0xdfe800ff) for rid 10 of pci0:0:31:4
	map[20]: type I/O Port, range 32, base 0xefa0, size  5, enabled
pcib0: allocated type 4 (0xefa0-0xefbf) for rid 20 of pci0:0:31:4
pcib0: matched entry for 0.31.INTA
pcib0: slot 31 INTA hardwired to IRQ 23
found->	vendor=0x8086, dev=0x19e0, revid=0x11
	domain=0, bus=0, slot=31, func=5
	class=0c-80-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0402, statreg=0x0000, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	map[10]: type Memory, range 32, base 0xdfe79000, size 12, enabled
pcib0: allocated type 3 (0xdfe79000-0xdfe79fff) for rid 10 of pci0:0:31:5
pci0: <base peripheral> at device 5.0 (no driver attached)
pcib1: <ACPI PCI-PCI bridge> irq 18 at device 6.0 on pci0
pcib0: allocated type 3 (0xdfd00000-0xdfdfffff) for rid 20 of pcib1
pcib1:   domain            0
pcib1:   secondary bus     1
pcib1:   subordinate bus   1
pcib1:   memory decode     0xdfd00000-0xdfdfffff
pcib1: could not get PCI interrupt routing table for \_SB_.PCI0.VRP2 - AE_NOT_FOUND
pci1: <ACPI PCI bus> on pcib1
pcib1: allocated bus range (1-1) for rid 0 of pci1
pci1: domain=0, physical bus=1
found->	vendor=0x8086, dev=0x19e2, revid=0x11
	domain=0, bus=1, slot=0, func=0
	class=0b-40-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0002, statreg=0x0010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=11
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message, 64 bit, vector masks
	MSI-X supports 17 messages in map 0x18
	map[18]: type Memory, range 64, base 0xdfd00000, size 18, enabled
pcib1: allocated memory range (0xdfd00000-0xdfd3ffff) for rid 18 of pci0:1:0:0
	map[20]: type Memory, range 64, base 0xdfd40000, size 18, enabled
pcib1: allocated memory range (0xdfd40000-0xdfd7ffff) for rid 20 of pci0:1:0:0
pcib0: matched entry for 0.6.INTA
pcib0: slot 6 INTA hardwired to IRQ 18
pcib1: slot 0 INTA is routed to irq 18
pci1: <processor> at device 0.0 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> mem 0xdfe00000-0xdfe1ffff irq 20 at device 14.0 on pci0
pcib2:   domain            0
pcib2:   secondary bus     2
pcib2:   subordinate bus   2
pci2: <ACPI PCI bus> on pcib2
pcib2: allocated bus range (2-2) for rid 0 of pci2
pci2: domain=0, physical bus=2
pcib3: <ACPI PCI-PCI bridge> mem 0xdfe20000-0xdfe3ffff irq 22 at device 16.0 on pci0
pcib3:   domain            0
pcib3:   secondary bus     3
pcib3:   subordinate bus   3
pci3: <ACPI PCI bus> on pcib3
pcib3: allocated bus range (3-3) for rid 0 of pci3
pci3: domain=0, physical bus=3
pcib4: <ACPI PCI-PCI bridge> mem 0xdfe40000-0xdfe5ffff irq 23 at device 17.0 on pci0
pcib4:   domain            0
pcib4:   secondary bus     4
pcib4:   subordinate bus   4
pci4: <ACPI PCI bus> on pcib4
pcib4: allocated bus range (4-4) for rid 0 of pci4
pci4: domain=0, physical bus=4
pci0: <base peripheral> at device 18.0 (no driver attached)
ahci0: <Intel Denverton AHCI SATA controller> port 0x1c20-0x1c27,0x1c28-0x1c2b,0x1c00-0x1c1f mem 0xdfe74000-0xdfe75fff,0xdfe7c000-0xdfe7c0ff,0xdfe7a000-0xdfe7a7ff irq 21 at device 20.0 on pci0
ahci0: attempting to allocate 8 MSI-X vectors (8 supported)
msi: routing MSI-X IRQ 264 to local APIC 28 vector 49
msi: routing MSI-X IRQ 265 to local APIC 0 vector 55
msi: routing MSI-X IRQ 266 to local APIC 8 vector 49
msi: routing MSI-X IRQ 267 to local APIC 20 vector 50
msi: routing MSI-X IRQ 268 to local APIC 28 vector 50
msi: routing MSI-X IRQ 269 to local APIC 0 vector 56
msi: routing MSI-X IRQ 270 to local APIC 8 vector 50
msi: routing MSI-X IRQ 271 to local APIC 20 vector 51
ahci0: using IRQs 264-271 for MSI-X
ahci0: AHCI v1.31 with 5 6Gbps ports, Port Multiplier supported
ahci0: Caps: 64bit NCQ SNTF MPS SS ALP AL CLO 6Gbps PM PMD SSC PSC 32cmd 5ports
ahci0: Caps2: DESO SADM SDS APST
ahcich0: not probed (disabled)
ahcich1: <AHCI channel> at channel 1 on ahci0
ahcich1: Caps: HPCP
ahcich2: not probed (disabled)
ahcich3: <AHCI channel> at channel 3 on ahci0
ahcich3: Caps: HPCP
ahcich4: <AHCI channel> at channel 4 on ahci0
ahcich4: Caps: HPCP
ahcich5: <AHCI channel> at channel 5 on ahci0
ahcich5: Caps: HPCP
ahcich6: <AHCI channel> at channel 6 on ahci0
ahcich6: Caps: HPCP
xhci0: <Intel Denverton USB 3.0 controller> mem 0xdfe60000-0xdfe6ffff irq 19 at device 21.0 on pci0
xhci0: 32 bytes context size, 64-bit DMA
xhci0: attempting to allocate 1 MSI vectors (8 supported)
msi: routing MSI IRQ 272 to local APIC 28 vector 51
xhci0: using IRQ 272 for MSI
xhci0: MSI enabled
usbus0 on xhci0
xhci0: usbpf: Attached
usbus0: 5.0Gbps Super Speed USB v3.0
pcib5: <ACPI PCI-PCI bridge> irq 16 at device 22.0 on pci0
pcib0: allocated type 3 (0xdf300000-0xdf7fffff) for rid 20 of pcib5
pcib0: allocated type 3 (0xde800000-0xdecfffff) for rid 24 of pcib5
pcib5:   domain            0
pcib5:   secondary bus     5
pcib5:   subordinate bus   5
pcib5:   memory decode     0xdf300000-0xdf7fffff
pcib5:   prefetched decode 0xde800000-0xdecfffff
pcib5: could not get PCI interrupt routing table for \_SB_.PCI0.VRP0 - AE_NOT_FOUND
pci5: <ACPI PCI bus> on pcib5
pcib5: allocated bus range (5-5) for rid 0 of pci5
pci5: domain=0, physical bus=5
found->	vendor=0x8086, dev=0x15c4, revid=0x11
	domain=0, bus=5, slot=0, func=0
	class=02-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0002, statreg=0x0010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=11
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message, 64 bit, vector masks
	MSI-X supports 64 messages in map 0x20
	map[10]: type Prefetchable Memory, range 64, base 0xde800000, size 21, enabled
pcib5: allocated prefetch range (0xde800000-0xde9fffff) for rid 10 of pci0:5:0:0
	map[20]: type Prefetchable Memory, range 64, base 0xdec00000, size 14, enabled
pcib5: allocated prefetch range (0xdec00000-0xdec03fff) for rid 20 of pci0:5:0:0
pcib0: matched entry for 0.22.INTA
pcib0: slot 22 INTA hardwired to IRQ 16
pcib5: slot 0 INTA is routed to irq 16
found->	vendor=0x8086, dev=0x15c4, revid=0x11
	domain=0, bus=5, slot=0, func=1
	class=02-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0002, statreg=0x0010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=10
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message, 64 bit, vector masks
	MSI-X supports 64 messages in map 0x20
	map[10]: type Prefetchable Memory, range 64, base 0xdea00000, size 21, enabled
pcib5: allocated prefetch range (0xdea00000-0xdebfffff) for rid 10 of pci0:5:0:1
	map[20]: type Prefetchable Memory, range 64, base 0xdec04000, size 14, enabled
pcib5: allocated prefetch range (0xdec04000-0xdec07fff) for rid 20 of pci0:5:0:1
pcib0: no PRT entry for 0.22.INTB
ix0: <Intel(R) PRO/10GbE PCI-Express Network Driver> mem 0xde800000-0xde9fffff,0xdec00000-0xdec03fff irq 16 at device 0.0 on pci5
ix0: Using 2048 TX descriptors and 2048 RX descriptors
ix0: msix_init qsets capped at 64
ix0: intr CPUs: 4 queue msgs: 63 admincnt: 1
ix0: Using 4 RX queues 4 TX queues
ix0: attempting to allocate 5 MSI-X vectors (64 supported)
msi: routing MSI-X IRQ 273 to local APIC 0 vector 57
msi: routing MSI-X IRQ 274 to local APIC 8 vector 51
msi: routing MSI-X IRQ 275 to local APIC 20 vector 52
msi: routing MSI-X IRQ 276 to local APIC 28 vector 52
msi: routing MSI-X IRQ 277 to local APIC 0 vector 58
ix0: using IRQs 273-277 for MSI-X
ix0: Using MSI-X interrupts with 5 vectors
ix0: allocated for 4 queues
ix0: allocated for 4 rx queues
<6>ix0: bpf attached
<6>ix0: Ethernet address: 00:08:a2:0e:a8:2d
<6>ix0: netmap queues/slots: TX 4/2048, RX 4/2048
ix1: <Intel(R) PRO/10GbE PCI-Express Network Driver> mem 0xdea00000-0xdebfffff,0xdec04000-0xdec07fff irq 10 at device 0.1 on pci5
ix1: Using 2048 TX descriptors and 2048 RX descriptors
ix1: msix_init qsets capped at 64
ix1: intr CPUs: 4 queue msgs: 63 admincnt: 1
ix1: Using 4 RX queues 4 TX queues
ix1: attempting to allocate 5 MSI-X vectors (64 supported)
msi: routing MSI-X IRQ 278 to local APIC 8 vector 52
msi: routing MSI-X IRQ 279 to local APIC 20 vector 53
msi: routing MSI-X IRQ 280 to local APIC 28 vector 53
msi: routing MSI-X IRQ 281 to local APIC 0 vector 59
msi: routing MSI-X IRQ 282 to local APIC 8 vector 53
ix1: using IRQs 278-282 for MSI-X
ix1: Using MSI-X interrupts with 5 vectors
ix1: allocated for 4 queues
ix1: allocated for 4 rx queues
msi: Assigning MSI-X IRQ 278 to local APIC 0 vector 60
msi: Assigning MSI-X IRQ 279 to local APIC 8 vector 52
msi: Assigning MSI-X IRQ 280 to local APIC 20 vector 53
msi: Assigning MSI-X IRQ 281 to local APIC 28 vector 53
<6>ix1: bpf attached
<6>ix1: Ethernet address: 00:08:a2:0e:a8:2e
<6>ix1: netmap queues/slots: TX 4/2048, RX 4/2048
pcib6: <ACPI PCI-PCI bridge> irq 17 at device 23.0 on pci0
pcib0: allocated type 3 (0xdf800000-0xdfcfffff) for rid 20 of pcib6
pcib0: allocated type 3 (0xdee00000-0xdf2fffff) for rid 24 of pcib6
pcib6:   domain            0
pcib6:   secondary bus     6
pcib6:   subordinate bus   6
pcib6:   memory decode     0xdf800000-0xdfcfffff
pcib6:   prefetched decode 0xdee00000-0xdf2fffff
pcib6: could not get PCI interrupt routing table for \_SB_.PCI0.VRP1 - AE_NOT_FOUND
pci6: <ACPI PCI bus> on pcib6
pcib6: allocated bus range (6-6) for rid 0 of pci6
pci6: domain=0, physical bus=6
found->	vendor=0x8086, dev=0x15c3, revid=0x11
	domain=0, bus=6, slot=0, func=0
	class=02-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0002, statreg=0x0010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=11
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message, 64 bit, vector masks
	MSI-X supports 64 messages in map 0x20
	map[10]: type Prefetchable Memory, range 64, base 0xdee00000, size 21, enabled
pcib6: allocated prefetch range (0xdee00000-0xdeffffff) for rid 10 of pci0:6:0:0
	map[20]: type Prefetchable Memory, range 64, base 0xdf200000, size 14, enabled
pcib6: allocated prefetch range (0xdf200000-0xdf203fff) for rid 20 of pci0:6:0:0
pcib0: matched entry for 0.23.INTA
pcib0: slot 23 INTA hardwired to IRQ 17
pcib6: slot 0 INTA is routed to irq 17
found->	vendor=0x8086, dev=0x15c3, revid=0x11
	domain=0, bus=6, slot=0, func=1
	class=02-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0002, statreg=0x0010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=10
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message, 64 bit, vector masks
	MSI-X supports 64 messages in map 0x20
	map[10]: type Prefetchable Memory, range 64, base 0xdf000000, size 21, enabled
pcib6: allocated prefetch range (0xdf000000-0xdf1fffff) for rid 10 of pci0:6:0:1
	map[20]: type Prefetchable Memory, range 64, base 0xdf204000, size 14, enabled
pcib6: allocated prefetch range (0xdf204000-0xdf207fff) for rid 20 of pci0:6:0:1
pcib0: no PRT entry for 0.23.INTB
ix2: <Intel(R) PRO/10GbE PCI-Express Network Driver> mem 0xdee00000-0xdeffffff,0xdf200000-0xdf203fff irq 17 at device 0.0 on pci6
ix2: Using 2048 TX descriptors and 2048 RX descriptors
ix2: msix_init qsets capped at 64
ix2: intr CPUs: 4 queue msgs: 63 admincnt: 1
ix2: Using 4 RX queues 4 TX queues
ix2: attempting to allocate 5 MSI-X vectors (64 supported)
msi: routing MSI-X IRQ 283 to local APIC 20 vector 54
msi: routing MSI-X IRQ 284 to local APIC 28 vector 54
msi: routing MSI-X IRQ 285 to local APIC 0 vector 59
msi: routing MSI-X IRQ 286 to local APIC 8 vector 54
msi: routing MSI-X IRQ 287 to local APIC 20 vector 55
ix2: using IRQs 283-287 for MSI-X
ix2: Using MSI-X interrupts with 5 vectors
ix2: allocated for 4 queues
ix2: allocated for 4 rx queues
msi: Assigning MSI-X IRQ 283 to local APIC 0 vector 61
msi: Assigning MSI-X IRQ 284 to local APIC 8 vector 55
msi: Assigning MSI-X IRQ 285 to local APIC 20 vector 54
msi: Assigning MSI-X IRQ 286 to local APIC 28 vector 54
<6>ix2: bpf attached
<6>ix2: Ethernet address: 00:08:a2:0e:a8:2f
mdio0: <MDIO> on ix2
e6000sw0: <Marvell 88E6190> on mdio0
e6000sw0: single-chip addressing mode
e6000sw0: PHY at port 1
miibus0: <MII bus> on e6000sw0
e1000phy0: <Marvell 88E1000 Gigabit PHY> PHY 1 on miibus0
e1000phy0: OUI 0x000ac2, model 0x0000, rev. 0
e1000phy0:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
e6000sw0: PHY at port 2
miibus1: <MII bus> on e6000sw0
e1000phy1: <Marvell 88E1000 Gigabit PHY> PHY 2 on miibus1
e1000phy1: OUI 0x000ac2, model 0x0000, rev. 0
e1000phy1:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
e6000sw0: PHY at port 3
miibus2: <MII bus> on e6000sw0
e1000phy2: <Marvell 88E1000 Gigabit PHY> PHY 3 on miibus2
e1000phy2: OUI 0x000ac2, model 0x0000, rev. 0
e1000phy2:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
e6000sw0: PHY at port 4
miibus3: <MII bus> on e6000sw0
e1000phy3: <Marvell 88E1000 Gigabit PHY> PHY 4 on miibus3
e1000phy3: OUI 0x000ac2, model 0x0000, rev. 0
e1000phy3:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
e6000sw0: PHY at port 5
miibus4: <MII bus> on e6000sw0
e1000phy4: <Marvell 88E1000 Gigabit PHY> PHY 5 on miibus4
e1000phy4: OUI 0x000ac2, model 0x0000, rev. 0
e1000phy4:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
e6000sw0: PHY at port 6
miibus5: <MII bus> on e6000sw0
e1000phy5: <Marvell 88E1000 Gigabit PHY> PHY 6 on miibus5
e1000phy5: OUI 0x000ac2, model 0x0000, rev. 0
e1000phy5:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
e6000sw0: PHY at port 7
miibus6: <MII bus> on e6000sw0
e1000phy6: <Marvell 88E1000 Gigabit PHY> PHY 7 on miibus6
e1000phy6: OUI 0x000ac2, model 0x0000, rev. 0
e1000phy6:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
e6000sw0: PHY at port 8
miibus7: <MII bus> on e6000sw0
e1000phy7: <Marvell 88E1000 Gigabit PHY> PHY 8 on miibus7
e1000phy7: OUI 0x000ac2, model 0x0000, rev. 0
e1000phy7:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
e6000sw0: CPU port at 9
e6000sw0: fixed port at 9
e6000sw0: CPU port at 10
e6000sw0: fixed port at 10
e6000sw0: switch is ready.
etherswitch0: <Switch controller> on e6000sw0
<6>ix2: netmap queues/slots: TX 4/2048, RX 4/2048
<6>e6000sw0port1: link state changed to UP
<6>e6000sw0port2: link state changed to DOWN
<6>e6000sw0port3: link state changed to DOWN
<6>e6000sw0port4: link state changed to DOWN
<6>e6000sw0port5: link state changed to DOWN
ix3: <Intel(R) PRO/10GbE PCI-Express Network Driver>
<6>e6000sw0port6: link state changed to DOWN
 mem 0xdf000000-0xdf1fffff,0xdf204000-0xdf207fff irq 10 at device 0.1 on pci6
<6>e6000sw0port7: link state changed to DOWN
<6>e6000sw0port8: link state changed to DOWN
ix3: Using 2048 TX descriptors and 2048 RX descriptors
ix3: msix_init qsets capped at 64
ix3: intr CPUs: 4 queue msgs: 63 admincnt: 1
ix3: Using 4 RX queues 4 TX queues
ix3: attempting to allocate 5 MSI-X vectors (64 supported)
msi: routing MSI-X IRQ 288 to local APIC 28 vector 55
msi: routing MSI-X IRQ 289 to local APIC 0 vector 59
msi: routing MSI-X IRQ 290 to local APIC 8 vector 54
msi: routing MSI-X IRQ 291 to local APIC 20 vector 56
msi: routing MSI-X IRQ 292 to local APIC 28 vector 56
ix3: using IRQs 288-292 for MSI-X
ix3: Using MSI-X interrupts with 5 vectors
ix3: allocated for 4 queues
ix3: allocated for 4 rx queues
msi: Assigning MSI-X IRQ 288 to local APIC 0 vector 62
msi: Assigning MSI-X IRQ 289 to local APIC 8 vector 56
msi: Assigning MSI-X IRQ 290 to local APIC 20 vector 57
msi: Assigning MSI-X IRQ 291 to local APIC 28 vector 55
<6>ix3: bpf attached
<6>ix3: Ethernet address: 00:08:a2:0e:a8:30
<6>ix3: netmap queues/slots: TX 4/2048, RX 4/2048
pci0: <simple comms> at device 24.0 (no driver attached)
sdhci_pci0: <Intel Denverton eMMC 5.0 Controller> mem 0xdfe77000-0xdfe77fff,0xdfe78000-0xdfe78fff irq 16 at device 28.0 on pci0
sdhci_pci0-slot0: 200MHz HS 8bits VDD: 1.8V VCCQ: 3.3V 1.8V DRV: B DMA embedded
sdhci_pci0-slot0: eMMC: DDR52
sdhci_pci0-slot0: UHS-I: SDR12 SDR25 SDR50 SDR104 DDR50
sdhci_pci0-slot0: Re-tuning count 0 secs, mode 1
sdhci_pci0-slot0: ============== REGISTER DUMP ==============
sdhci_pci0-slot0: Sys addr: 0x03105200 | Version:  0x00001002
sdhci_pci0-slot0: Blk size: 0x00000200 | Blk cnt:  0x00000000
sdhci_pci0-slot0: Argument: 0x02f036b8 | Trn mode: 0x00000036
sdhci_pci0-slot0: Present:  0x1fff0000 | Host ctl: 0x00000000
sdhci_pci0-slot0: Power:    0x0000000b | Blk gap:  0x00000080
sdhci_pci0-slot0: Wake-up:  0x00000000 | Clock:    0x00000407
sdhci_pci0-slot0: Timeout:  0x0000000e | Int stat: 0x00000000
sdhci_pci0-slot0: Int enab: 0x01ff01ff | Sig enab: 0x00000000
sdhci_pci0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
sdhci_pci0-slot0: Caps:     0x546ec8b2 | Caps2:    0x80000007
sdhci_pci0-slot0: Max curr: 0x00000000 | ADMA err: 0x00000000
sdhci_pci0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
sdhci_pci0-slot0: ===========================================
sdhci_pci0: 1 slot(s) allocated
ioapic0: routing intpin 16 (PCI IRQ 16) to lapic 0 vector 59
sdhci_pci0-slot0: Card inserted
mmc0: <MMC/SD bus> on sdhci_pci0
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
pci0: <memory> at device 31.2 (no driver attached)
pci0: <serial bus, SMBus> at device 31.4 (no driver attached)
pci0: <serial bus> at device 31.5 (no driver attached)
uart0: <Non-standard ns8250 class UART with FIFOs> port 0x3f8-0x3ff irq 19 flags 0x10 on acpi0
uart0: console (115200,n,8,1)
ioapic0: routing intpin 19 (PCI IRQ 19) to lapic 8 vector 54
uart0: fast interrupt
uart0: PPS capture mode: DCD
uart1: <Non-standard ns8250 class UART with FIFOs> port 0x2f8-0x2ff irq 18 on acpi0
ioapic0: routing intpin 18 (PCI IRQ 18) to lapic 20 vector 56
uart1: fast interrupt
uart1: PPS capture mode: DCD
ahc_isa_identify 0: ioport 0xc00 alloc failed
ahc_isa_identify 1: ioport 0x1c00 alloc failed
ahc_isa_identify 2: ioport 0x2c00 alloc failed
ahc_isa_identify 3: ioport 0x3c00 alloc failed
ahc_isa_identify 4: ioport 0x4c00 alloc failed
ahc_isa_identify 5: ioport 0x5c00 alloc failed
ahc_isa_identify 6: ioport 0x6c00 alloc failed
ahc_isa_identify 7: ioport 0x7c00 alloc failed
ahc_isa_identify 8: ioport 0x8c00 alloc failed
ahc_isa_identify 9: ioport 0x9c00 alloc failed
ahc_isa_identify 10: ioport 0xac00 alloc failed
ahc_isa_identify 11: ioport 0xbc00 alloc failed
ahc_isa_identify 12: ioport 0xcc00 alloc failed
ahc_isa_identify 13: ioport 0xdc00 alloc failed
ahc_isa_identify 14: ioport 0xec00 alloc failed
pcib0: allocated type 3 (0xb0000-0xb07ff) for rid 0 of orm0
pcib0: allocated type 3 (0xb0800-0xb0fff) for rid 0 of orm0
pcib0: allocated type 3 (0xb1000-0xb17ff) for rid 0 of orm0
pcib0: allocated type 3 (0xb1800-0xb1fff) for rid 0 of orm0
pcib0: allocated type 3 (0xb2000-0xb27ff) for rid 0 of orm0
pcib0: allocated type 3 (0xb2800-0xb2fff) for rid 0 of orm0
pcib0: allocated type 3 (0xb3000-0xb37ff) for rid 0 of orm0
pcib0: allocated type 3 (0xb3800-0xb3fff) for rid 0 of orm0
pcib0: allocated type 3 (0xb4000-0xb47ff) for rid 0 of orm0
pcib0: allocated type 3 (0xb4800-0xb4fff) for rid 0 of orm0
pcib0: allocated type 3 (0xb5000-0xb57ff) for rid 0 of orm0
pcib0: allocated type 3 (0xb5800-0xb5fff) for rid 0 of orm0
pcib0: allocated type 3 (0xb6000-0xb67ff) for rid 0 of orm0
pcib0: allocated type 3 (0xb6800-0xb6fff) for rid 0 of orm0
pcib0: allocated type 3 (0xb7000-0xb77ff) for rid 0 of orm0
pcib0: allocated type 3 (0xb7800-0xb7fff) for rid 0 of orm0
pcib0: allocated type 3 (0xb8000-0xb87ff) for rid 0 of orm0
pcib0: allocated type 3 (0xb8800-0xb8fff) for rid 0 of orm0
pcib0: allocated type 3 (0xb9000-0xb97ff) for rid 0 of orm0
pcib0: allocated type 3 (0xb9800-0xb9fff) for rid 0 of orm0
pcib0: allocated type 3 (0xba000-0xba7ff) for rid 0 of orm0
pcib0: allocated type 3 (0xba800-0xbafff) for rid 0 of orm0
pcib0: allocated type 3 (0xbb000-0xbb7ff) for rid 0 of orm0
pcib0: allocated type 3 (0xbb800-0xbbfff) for rid 0 of orm0
pcib0: allocated type 3 (0xbc000-0xbc7ff) for rid 0 of orm0
pcib0: allocated type 3 (0xbc800-0xbcfff) for rid 0 of orm0
pcib0: allocated type 3 (0xbd000-0xbd7ff) for rid 0 of orm0
pcib0: allocated type 3 (0xbd800-0xbdfff) for rid 0 of orm0
pcib0: allocated type 3 (0xbe000-0xbe7ff) for rid 0 of orm0
pcib0: allocated type 3 (0xbe800-0xbefff) for rid 0 of orm0
pcib0: allocated type 3 (0xbf000-0xbf7ff) for rid 0 of orm0
pcib0: allocated type 3 (0xbf800-0xbffff) for rid 0 of orm0
pcib0: allocated type 3 (0xc0000-0xc07ff) for rid 0 of orm0
pcib0: allocated type 3 (0xc0000-0xc0fff) for rid 0 of orm0
pcib0: allocated type 3 (0xc1000-0xc17ff) for rid 1 of orm0
pcib0: allocated type 3 (0xc1800-0xc1fff) for rid 1 of orm0
pcib0: allocated type 3 (0xc2000-0xc27ff) for rid 1 of orm0
pcib0: allocated type 3 (0xc2800-0xc2fff) for rid 1 of orm0
pcib0: allocated type 3 (0xc3000-0xc37ff) for rid 1 of orm0
pcib0: allocated type 3 (0xc3800-0xc3fff) for rid 1 of orm0
pcib0: allocated type 3 (0xc4000-0xc47ff) for rid 1 of orm0
pcib0: allocated type 3 (0xc4800-0xc4fff) for rid 1 of orm0
pcib0: allocated type 3 (0xc5000-0xc57ff) for rid 1 of orm0
pcib0: allocated type 3 (0xc5800-0xc5fff) for rid 1 of orm0
pcib0: allocated type 3 (0xc6000-0xc67ff) for rid 1 of orm0
pcib0: allocated type 3 (0xc6800-0xc6fff) for rid 1 of orm0
pcib0: allocated type 3 (0xc7000-0xc77ff) for rid 1 of orm0
pcib0: allocated type 3 (0xc7800-0xc7fff) for rid 1 of orm0
pcib0: allocated type 3 (0xc8000-0xc87ff) for rid 1 of orm0
pcib0: allocated type 3 (0xc8800-0xc8fff) for rid 1 of orm0
pcib0: allocated type 3 (0xc9000-0xc97ff) for rid 1 of orm0
pcib0: allocated type 3 (0xc9800-0xc9fff) for rid 1 of orm0
pcib0: allocated type 3 (0xca000-0xca7ff) for rid 1 of orm0
pcib0: allocated type 3 (0xca800-0xcafff) for rid 1 of orm0
pcib0: allocated type 3 (0xcb000-0xcb7ff) for rid 1 of orm0
pcib0: allocated type 3 (0xcb800-0xcbfff) for rid 1 of orm0
pcib0: allocated type 3 (0xcc000-0xcc7ff) for rid 1 of orm0
pcib0: allocated type 3 (0xcc800-0xccfff) for rid 1 of orm0
pcib0: allocated type 3 (0xcd000-0xcd7ff) for rid 1 of orm0
pcib0: allocated type 3 (0xcd800-0xcdfff) for rid 1 of orm0
pcib0: allocated type 3 (0xce000-0xce7ff) for rid 1 of orm0
pcib0: allocated type 3 (0xce800-0xcefff) for rid 1 of orm0
pcib0: allocated type 3 (0xcf000-0xcf7ff) for rid 1 of orm0
pcib0: allocated type 3 (0xcf800-0xcffff) for rid 1 of orm0
pcib0: allocated type 3 (0xd0000-0xd07ff) for rid 1 of orm0
pcib0: allocated type 3 (0xd0800-0xd0fff) for rid 1 of orm0
pcib0: allocated type 3 (0xd1000-0xd17ff) for rid 1 of orm0
pcib0: allocated type 3 (0xd1800-0xd1fff) for rid 1 of orm0
pcib0: allocated type 3 (0xd2000-0xd27ff) for rid 1 of orm0
pcib0: allocated type 3 (0xd2800-0xd2fff) for rid 1 of orm0
pcib0: allocated type 3 (0xd3000-0xd37ff) for rid 1 of orm0
pcib0: allocated type 3 (0xd3800-0xd3fff) for rid 1 of orm0
pcib0: allocated type 3 (0xd4000-0xd47ff) for rid 1 of orm0
pcib0: allocated type 3 (0xd4800-0xd4fff) for rid 1 of orm0
pcib0: allocated type 3 (0xd5000-0xd57ff) for rid 1 of orm0
pcib0: allocated type 3 (0xd5800-0xd5fff) for rid 1 of orm0
pcib0: allocated type 3 (0xd6000-0xd67ff) for rid 1 of orm0
pcib0: allocated type 3 (0xd6800-0xd6fff) for rid 1 of orm0
pcib0: allocated type 3 (0xd7000-0xd77ff) for rid 1 of orm0
pcib0: allocated type 3 (0xd7800-0xd7fff) for rid 1 of orm0
pcib0: allocated type 3 (0xd8000-0xd87ff) for rid 1 of orm0
pcib0: allocated type 3 (0xd8800-0xd8fff) for rid 1 of orm0
pcib0: allocated type 3 (0xd9000-0xd97ff) for rid 1 of orm0
pcib0: allocated type 3 (0xd9800-0xd9fff) for rid 1 of orm0
pcib0: allocated type 3 (0xda000-0xda7ff) for rid 1 of orm0
pcib0: allocated type 3 (0xda800-0xdafff) for rid 1 of orm0
pcib0: allocated type 3 (0xdb000-0xdb7ff) for rid 1 of orm0
pcib0: allocated type 3 (0xdb800-0xdbfff) for rid 1 of orm0
pcib0: allocated type 3 (0xdc000-0xdc7ff) for rid 1 of orm0
pcib0: allocated type 3 (0xdc800-0xdcfff) for rid 1 of orm0
pcib0: allocated type 3 (0xdd000-0xdd7ff) for rid 1 of orm0
pcib0: allocated type 3 (0xdd800-0xddfff) for rid 1 of orm0
pcib0: allocated type 3 (0xde000-0xde7ff) for rid 1 of orm0
pcib0: allocated type 3 (0xde800-0xdefff) for rid 1 of orm0
pcib0: allocated type 3 (0xdf000-0xdf7ff) for rid 1 of orm0
pcib0: allocated type 3 (0xdf800-0xdffff) for rid 1 of orm0
isa_probe_children: disabling PnP devices
atrtc: atrtc0 already exists; skipping it
attimer: attimer0 already exists; skipping it
sc: sc0 already exists; skipping it
uart: uart0 already exists; skipping it
uart: uart1 already exists; skipping it
isa_probe_children: probing non-PnP devices
orm0: <ISA Option ROMs> at iomem 0xc0000-0xc0fff,0xee800-0xeffff pnpid ORM0000 on isa0
sc0 failed to probe on isa0
vga0 failed to probe on isa0
pcib0: allocated type 4 (0x60-0x60) for rid 0 of atkbdc0
pcib0: allocated type 4 (0x64-0x64) for rid 1 of atkbdc0
atkbdc0: AT keyboard controller not found
atkbdc0 failed to probe at port 0x60,0x64 on isa0
pcib0: allocated type 4 (0x3f0-0x3f5) for rid 0 of fdc0
pcib0: allocated type 4 (0x3f7-0x3f7) for rid 1 of fdc0
fdc0 failed to probe at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
ppc0: cannot reserve I/O port range
ppc0 failed to probe at irq 7 on isa0
isa_probe_children: probing PnP devices
AcpiOsExecute: task queue not started
AcpiOsExecute: task queue not started
AcpiOsExecute: task queue not started
AcpiOsExecute: task queue not started
est0: <Enhanced SpeedStep Frequency Control> on cpu0
est1: <Enhanced SpeedStep Frequency Control> on cpu1
est2: <Enhanced SpeedStep Frequency Control> on cpu2
est3: <Enhanced SpeedStep Frequency Control> on cpu3
Device configuration finished.
procfs registered
ZFS filesystem version: 5
ZFS storage pool version: features support (5000)
Timecounters tick every 1.000 msec
<6>enc0: bpf attached
vlan: initialized, using hash tables with chaining
<6>lo0: bpf attached
IPsec: Initialized Security Association Processing.
tcp_init: net.inet.tcp.tcbhashsize auto tuned to 65536
<6>pflog0: bpf attached
<6>pfsync0: bpf attached
AcpiOsExecute: enqueue 4 pending tasks
hptnr: no controller detected.
hptrr: no controller detected.
hpt27xx: no controller detected.
ahcich1: AHCI reset...
sdhci_pci0-slot0: Divider 250 for freq 400000 (base 200000000)
sdhci_pci0-slot0: Divider 250 for freq 400000 (base 200000000)
ahcich1: SATA connect timeout time=10000us status=00000000
mmc0: ahcich1: AHCI reset: device not found
ahcich3: AHCI reset...
Probing bus
sdhci_pci0-slot0: Divider 250 for freq 400000 (base 200000000)
ugen0.1: <0x8086 XHCI root HUB> at usbus0
sdhci_pci0-slot0: ahcich3: SATA connect timeout time=10000us status=00000000
ahcich3: AHCI reset: device not found
ahcich4: AHCI reset...
Divider 250 for freq 400000 (base 200000000)
uhub0: <0x8086 XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0
ahcich4: SATA connect timeout time=10000us status=00000000
ahcich4: AHCI reset: device not found
ahcich5: AHCI reset...
mmc0: SD probe: failed
mmc0: MMC probe: OK (OCR: 0x40ff8080)
sdhci_pci0-slot0: Divider 250 for freq 400000 (base 200000000)
ahcich5: SATA connect timeout time=10000us status=00000000
ahcich5: AHCI reset: device not found
sdhci_pci0-slot0: ahcich6: AHCI reset...
Divider 250 for freq 400000 (base 200000000)
mmc0: Current OCR: 0x00ff8080
ahcich6: SATA connect timeout time=10000us status=00000000
ahcich6: AHCI reset: device not found
mmc0: Probing cards
mmc0: New card detected (CID 150100424a54443452037a69fe1dc400)
mmc0: New card detected (CSD d02701320f5903fff6dbffef8e404000)
sdhci_pci0-slot0: Divider 250 for freq 400000 (base 200000000)
sdhci_pci0-slot0: Divider 250 for freq 400000 (base 200000000)
mmc0: Card at relative address 0x0002 added:
mmc0:  card: MMCHC BJTD4R 0.3 SN 7A69FE1D MFG 12/2017 by 21 0x0000
mmc0:  quirks: 0
mmc0:  bus: 8bit, 200MHz (HS400 with enhanced strobe timing)
mmc0:  memory: 61071360 blocks, erase sector 1024 blocks
sdhci_pci0-slot0: Divider 250 for freq 400000 (base 200000000)
mmc0: setting transfer rate to 52.000MHz (dual data rate timing)
sdhci_pci0-slot0: Divider 250 for freq 400000 (base 200000000)
sdhci_pci0-slot0: Divider 250 for freq 400000 (base 200000000)
sdhci_pci0-slot0: Divider 250 for freq 400000 (base 200000000)
sdhci_pci0-slot0: Divider 2 for freq 50000000 (base 200000000)
sdhci_pci0-slot0: Divider 2 for freq 50000000 (base 200000000)
mmcsd0: taking advantage of TRIM
mmcsd0: cache size 65536KB
GEOM: new disk mmcsd0
mmcsd0: 31GB <MMCHC BJTD4R 0.3 SN 7A69FE1D MFG 12/2017 by 21 0x0000> at mmc0 50.0MHz/8bit/65535-block
mmcsd0boot0: 4MB partition 1 at mmcsd0
mmcsd0boot1: 4MB partition 2 at mmcsd0
mmcsd0rpmb: 4MB partition 3 at mmcsd0
pci0: driver added
found->	vendor=0x8086, dev=0x19a2, revid=0x11
	domain=0, bus=0, slot=5, func=0
	class=08-07-00, hdrtype=0x00, mfdev=0
GEOM: new disk mmcsd0boot0
	cmdreg=0x0004, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=23
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message, vector masks
pci0:0:5:0: reprobing on driver added
GEOM: new disk mmcsd0boot1
found->	vendor=0x8086, dev=0x19ac, revid=0x11
	domain=0, bus=0, slot=18, func=0
	class=08-80-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0006, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=16
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message, 64 bit, vector masks
pci0:0:18:0: reprobing on driver added
found->	vendor=0x8086, dev=0x19d3, revid=0x11
	domain=0, bus=0, slot=24, func=0
	class=07-80-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0006, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=16
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message, 64 bit
pci0:0:24:0: reprobing on driver added
found->	vendor=0x8086, dev=0x19de, revid=0x11
	domain=0, bus=0, slot=31, func=2
	class=05-80-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0006, statreg=0x0000, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
pci0:0:31:2: reprobing on driver added
found->	vendor=0x8086, dev=0x19df, revid=0x11
	domain=0, bus=0, slot=31, func=4
	class=0c-05-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0003, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=23
pci0:0:31:4: reprobing on driver added
found->	vendor=0x8086, dev=0x19e0, revid=0x11
	domain=0, bus=0, slot=31, func=5
	class=0c-80-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0402, statreg=0x0000, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
pci0:0:31:5: reprobing on driver added
pci1: driver added
found->	vendor=0x8086, dev=0x19e2, revid=0x11
	domain=0, bus=1, slot=0, func=0
	class=0b-40-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0002, statreg=0x0010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=18
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message, 64 bit, vector masks
	MSI-X supports 17 messages in map 0x18
pci0:1:0:0: reprobing on driver added
pci2: driver added
pci3: driver added
pci4: driver added
pci5: driver added
pci6: driver added
pci0: driver added
found->	vendor=0x8086, dev=0x19a2, revid=0x11
	domain=0, bus=0, slot=5, func=0
	class=08-07-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0004, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=23
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message, vector masks
pci0:0:5:0: reprobing on driver added
found->	vendor=0x8086, dev=0x19ac, revid=0x11
	domain=0, bus=0, slot=18, func=0
	class=08-80-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0006, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=16
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message, 64 bit, vector masks
pci0:0:18:0: reprobing on driver added
found->	vendor=0x8086, dev=0x19d3, revid=0x11
	domain=0, bus=0, slot=24, func=0
	class=07-80-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0006, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=16
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message, 64 bit
pci0:0:24:0: reprobing on driver added
found->	vendor=0x8086, dev=0x19de, revid=0x11
	domain=0, bus=0, slot=31, func=2
	class=05-80-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0006, statreg=0x0000, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
pci0:0:31:2: reprobing on driver added
found->	vendor=0x8086, dev=0x19df, revid=0x11
	domain=0, bus=0, slot=31, func=4
	class=0c-05-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0003, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=23
pci0:0:31:4: reprobing on driver added
found->	vendor=0x8086, dev=0x19e0, revid=0x11
	domain=0, bus=0, slot=31, func=5
	class=0c-80-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0402, statreg=0x0000, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
pci0:0:31:5: reprobing on driver added
pci1: driver added
found->	vendor=0x8086, dev=0x19e2, revid=0x11
	domain=0, bus=1, slot=0, func=0
	class=0b-40-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0002, statreg=0x0010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=18
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message, 64 bit, vector masks
	MSI-X supports 17 messages in map 0x18
pci0:1:0:0: reprobing on driver added
pci2: driver added
pci3: driver added
pci4: driver added
pci5: driver added
pci6: driver added
Trying to mount root from zfs:zroot/ROOT/default []...
Root mount waiting for: CAM usbus0
uhub0: 8 ports with 8 removable, self powered
Root mount waiting for: CAM
Root mount waiting for: CAM
Root mount waiting for: CAM
Root mount waiting for: CAM
Root mount waiting for: CAM
Root mount waiting for: CAM
Root mount waiting for: CAM
Root mount waiting for: CAM
atrtc0: providing initial system time
start_init: trying /sbin/init
<118>Configuring crash dumps...
<118>Using /dev/mmcsd0p2 for dump device.
<118>Filesystems are clean, continuing...
<118>Mounting filesystems...
<118>
<118>        __
<118> _ __  / _|___  ___ _ __  ___  ___      _
<118>| '_ \| |_/ __|/ _ \ '_ \/ __|/ _ \   _| |_
<118>| |_) |  _\__ \  __/ | | \__ \  __/  |_   _|
<118>| .__/|_| |___/\___|_| |_|___/\___|    |_|
<118>|_|
<118>
<118>
<118>Welcome to Netgate pfSense Plus 21.05-DEVELOPMENT...
<118>
<118>No core dumps found.
<118>...ELF ldconfig path: /lib /usr/lib /usr/lib/compat /usr/local/lib /usr/local/lib/compat/pkg /usr/lib/engines /usr/local/lib/compat/pkg /usr/local/lib/ipsec /usr/local/lib/perl5/5.32/mach/CORE
<118>32-bit compatibility ldconfig path:
<118>done.
<118>>>> Removing vital flag from php74... done.
<118>External config loader 1.0 is now starting... mmcsd0p1 mmcsd0p3
<118>Launching the init system...
cpuctl: access to MSR registers/cpuid info.
<118>Updating CPU Microcode...
CPU: Intel(R) Atom(TM) CPU C3558 @ 2.20GHz (2200.07-MHz K8-class CPU)
  Origin="GenuineIntel"  Id=0x506f1  Family=0x6  Model=0x5f  Stepping=1
  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Features2=0x4ff8ebbf<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,SDBG,CX16,xTPR,PDCM,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,TSCDLT,AESNI,XSAVE,OSXSAVE,RDRAND>
  AMD Features=0x2c100800<SYSCALL,NX,Page1GB,RDTSCP,LM>
  AMD Features2=0x101<LAHF,Prefetch>
  Structured Extended Features=0x2294e283<FSGSBASE,TSCADJ,SMEP,ERMS,NFPUSG,MPX,PQE,RDSEED,SMAP,CLFLUSHOPT,PROCTRACE,SHA>
  Structured Extended Features3=0xac000400<MD_CLEAR,IBPB,STIBP,ARCH_CAP,SSBD>
  XSAVE Features=0xf<XSAVEOPT,XSAVEC,XINUSE,XSAVES>
  IA32_ARCH_CAPS=0x69<RDCL_NO,SKIP_L1DFL_VME>
  VT-x: Basic Features=0xda0400<SMM,INS/OUTS,TRUE>
        Pin-Based Controls=0xff<ExtINT,NMI,VNMI,PreTmr,PostIntr>
        Primary Processor Controls=0xfff9fffe<INTWIN,TSCOff,HLT,INVLPG,MWAIT,RDPMC,RDTSC,CR3-LD,CR3-ST,CR8-LD,CR8-ST,TPR,NMIWIN,MOV-DR,IO,IOmap,MTF,MSRmap,MONITOR,PAUSE>
        Secondary Processor Controls=0x1d6fff<APIC,EPT,DT,RDTSCP,x2APIC,VPID,WBINVD,UG,APIC-reg,VID,PAUSE-loop,RDRAND,VMFUNC,VMCS,XSAVES>
        Exit Controls=0xda0400<PAT-LD,EFER-SV,PTMR-SV>
        Entry Controls=0xda0400
        EPT Features=0x6334141<XO,PW4,UC,WB,2M,1G,INVEPT,AD,single,all>
        VPID Features=0xf01<INVVPID,individual,single,all,single-globals>
  TSC: P-state invariant, performance statistics
DTLB: 4k pages, fully associative, 32 entries
Data TLB: 4 KBytes pages, 4-way set associative, 512 entries
Instruction TLB: 4 KByte pages, fully associative, 48 entries
DTLB: 2M/4M Byte pages, 4-way associative, 32 entries
L2 cache: 2048 kbytes, 16-way associative, 64 bytes/line
<118>Done.
<118>.... done.
<118>Initializing.................. done.
<118>Starting device manager (devd)...done.
<118>Loading configuration......done.
<118>Updating configuration...done.
<118>Checking config backups consistency.................................done.
<118>Setting up extended sysctls...done.
pci0: driver added
found->	vendor=0x8086, dev=0x19a2, revid=0x11
	domain=0, bus=0, slot=5, func=0
	class=08-07-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0004, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=23
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message, vector masks
pci0:0:5:0: reprobing on driver added
found->	vendor=0x8086, dev=0x19ac, revid=0x11
	domain=0, bus=0, slot=18, func=0
	class=08-80-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0006, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=16
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message, 64 bit, vector masks
pci0:0:18:0: reprobing on driver added
found->	vendor=0x8086, dev=0x19d3, revid=0x11
	domain=0, bus=0, slot=24, func=0
	class=07-80-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0006, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=16
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message, 64 bit
pci0:0:24:0: reprobing on driver added
found->	vendor=0x8086, dev=0x19de, revid=0x11
	domain=0, bus=0, slot=31, func=2
	class=05-80-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0006, statreg=0x0000, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
pci0:0:31:2: reprobing on driver added
found->	vendor=0x8086, dev=0x19df, revid=0x11
	domain=0, bus=0, slot=31, func=4
	class=0c-05-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0003, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=23
pci0:0:31:4: reprobing on driver added
found->	vendor=0x8086, dev=0x19e0, revid=0x11
	domain=0, bus=0, slot=31, func=5
	class=0c-80-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0402, statreg=0x0000, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
pci0:0:31:5: reprobing on driver added
pci1: driver added
found->	vendor=0x8086, dev=0x19e2, revid=0x11
	domain=0, bus=1, slot=0, func=0
	class=0b-40-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0002, statreg=0x0010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=18
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message, 64 bit, vector masks
	MSI-X supports 17 messages in map 0x18
pci0:1:0:0: reprobing on driver added
qat0: <Intel C3000 QuickAssist PF> mem 0xdfd00000-0xdfd3ffff,0xdfd40000-0xdfd7ffff irq 18 at device 0.0 on pci1
qat0: attempting to allocate 17 MSI-X vectors (17 supported)
msi: routing MSI-X IRQ 293 to local APIC 28 vector 57
msi: routing MSI-X IRQ 294 to local APIC 0 vector 63
msi: routing MSI-X IRQ 295 to local APIC 8 vector 57
msi: routing MSI-X IRQ 296 to local APIC 20 vector 58
msi: routing MSI-X IRQ 297 to local APIC 28 vector 58
msi: routing MSI-X IRQ 298 to local APIC 0 vector 64
msi: routing MSI-X IRQ 299 to local APIC 8 vector 58
msi: routing MSI-X IRQ 300 to local APIC 20 vector 59
msi: routing MSI-X IRQ 301 to local APIC 28 vector 59
msi: routing MSI-X IRQ 302 to local APIC 0 vector 65
msi: routing MSI-X IRQ 303 to local APIC 8 vector 59
msi: routing MSI-X IRQ 304 to local APIC 20 vector 60
msi: routing MSI-X IRQ 305 to local APIC 28 vector 60
msi: routing MSI-X IRQ 306 to local APIC 0 vector 66
msi: routing MSI-X IRQ 307 to local APIC 8 vector 60
msi: routing MSI-X IRQ 308 to local APIC 20 vector 61
msi: routing MSI-X IRQ 309 to local APIC 28 vector 61
qat0: using IRQs 293-309 for MSI-X
firmware: 'qat_c3xxxfw' version 111: 531100 bytes loaded at 0xffffffff84337000
firmware: 'qat_c3xxx_mmp' version 111: 120964 bytes loaded at 0xffffffff843b8aa0
msi: Assigning MSI-X IRQ 293 to local APIC 0 vector 67
msi: Assigning MSI-X IRQ 294 to local APIC 8 vector 61
msi: Assigning MSI-X IRQ 295 to local APIC 20 vector 62
msi: Assigning MSI-X IRQ 296 to local APIC 28 vector 57
msi: Assigning MSI-X IRQ 297 to local APIC 0 vector 63
msi: Assigning MSI-X IRQ 298 to local APIC 8 vector 57
msi: Assigning MSI-X IRQ 299 to local APIC 20 vector 58
msi: Assigning MSI-X IRQ 300 to local APIC 28 vector 58
msi: Assigning MSI-X IRQ 301 to local APIC 0 vector 64
msi: Assigning MSI-X IRQ 302 to local APIC 8 vector 58
msi: Assigning MSI-X IRQ 303 to local APIC 20 vector 59
msi: Assigning MSI-X IRQ 304 to local APIC 28 vector 59
msi: Assigning MSI-X IRQ 305 to local APIC 0 vector 65
msi: Assigning MSI-X IRQ 306 to local APIC 8 vector 59
msi: Assigning MSI-X IRQ 307 to local APIC 20 vector 60
msi: Assigning MSI-X IRQ 308 to local APIC 28 vector 60
crypto: assign qat0 driver id 1, flags 0x1000000
crypto: qat0 registers alg 11 flags 0 maxoplen 65535
crypto: qat0 registers alg 23 flags 0 maxoplen 65535
crypto: qat0 registers alg 22 flags 0 maxoplen 65535
crypto: qat0 registers alg 25 flags 0 maxoplen 65535
crypto: qat0 registers alg 26 flags 0 maxoplen 65535
crypto: qat0 registers alg 27 flags 0 maxoplen 65535
crypto: qat0 registers alg 28 flags 0 maxoplen 65535
crypto: qat0 registers alg 14 flags 0 maxoplen 65535
crypto: qat0 registers alg 7 flags 0 maxoplen 65535
crypto: qat0 registers alg 35 flags 0 maxoplen 65535
crypto: qat0 registers alg 18 flags 0 maxoplen 65535
crypto: qat0 registers alg 36 flags 0 maxoplen 65535
crypto: qat0 registers alg 19 flags 0 maxoplen 65535
crypto: qat0 registers alg 37 flags 0 maxoplen 65535
crypto: qat0 registers alg 20 flags 0 maxoplen 65535
pci2: driver added
pci3: driver added
pci4: driver added
pci5: driver added
pci6: driver added
coretemp0: <CPU On-Die Thermal Sensors> on cpu0
coretemp0: Setting TjMax=91
coretemp1: <CPU On-Die Thermal Sensors> on cpu1
coretemp1: Setting TjMax=91
coretemp2: <CPU On-Die Thermal Sensors> on cpu2
coretemp2: Setting TjMax=91
coretemp3: <CPU On-Die Thermal Sensors> on cpu3
coretemp3: Setting TjMax=91
<118>Setting timezone...done.
<118>Configuring loopback interface...
<6>lo0: link state changed to UP
<118>done.
<118>Starting syslog...done.
<118>Starting Secure Shell Services...done.
<118>Configuring switch...
<6>e6000sw0port1: link state changed to DOWN
<6>e6000sw0port1: link state changed to UP
<118>done.
<118>Setting up interfaces microcode...done.
<118>Starting PC/SC Smart Card Services...done.
<118>Configuring loopback interface...done.
<118>Creating wireless clone interfaces...done.
<118>Configuring LAGG interfaces...
<6>lagg0: bpf attached
<6>lagg0: IPv6 addresses on ix2 have been removed before adding it as a member to prevent IPv6 address scope violation.
<6>lagg0: link state changed to DOWN
<6>lagg0: IPv6 addresses on ix3 have been removed before adding it as a member to prevent IPv6 address scope violation.
<118>done.
<118>Configuring VLAN interfaces...
<6>vlan0: bpf attached
<6>vlan0: changing name to 'lagg0.4091'
<6>vlan1: bpf attached
<6>vlan1: changing name to 'lagg0.4090'
ix2: Link is up 1 Gbps Full Duplex 
<6>ix2: link state changed to UP
<6>lagg0: link state changed to UP
<6>lagg0.4090: link state changed to UP
<6>lagg0.4091: link state changed to UP
ix3: Link is up 1 Gbps Full Duplex 
<6>ix3: link state changed to UP
<118>done.
<118>Configuring QinQ interfaces...done.
<118>Configuring WAN2_10G interface...done.
<118>Configuring WAN3_SFP interface...
ix0: Link is up 10 Gbps Full Duplex 
<6>ix0: link state changed to UP
ix1: Link is up 1 Gbps Full Duplex 
<6>ix1: link state changed to UP
<118>done.
<118>Configuring OPT3 interface...done.
<118>Configuring LAN interface...done.
<118>Configuring WAN interface...
<6>pflog0: promiscuous mode enabled
<118>done.
<118>Configuring IPsec VTI interfaces...
<6>ipsec2000: bpf attached
<118>done.
<118>Configuring CARP settings...done.
<118>Syncing OpenVPN settings...done.
<118>Configuring firewall......done.
<118>Starting PFLOG...done.
<118>Setting up gateway monitors...done.
<118>Setting up static routes...done.
<118>Setting up DNSs...
<118>Starting DNS Resolver...done.
<118>Synchronizing user settings...done.
<118>Starting webConfigurator...done.
<118>Configuring CRON...done.
<118>Starting NTP Server...done.
<118>Starting DHCP service...done.
<118>Starting DHCPv6 service...done.
<118>Configuring firewall......done.
pci0: driver added
found->	vendor=0x8086, dev=0x19a2, revid=0x11
	domain=0, bus=0, slot=5, func=0
	class=08-07-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0004, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=23
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message, vector masks
pci0:0:5:0: reprobing on driver added
found->	vendor=0x8086, dev=0x19ac, revid=0x11
	domain=0, bus=0, slot=18, func=0
	class=08-80-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0006, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=16
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message, 64 bit, vector masks
pci0:0:18:0: reprobing on driver added
found->	vendor=0x8086, dev=0x19d3, revid=0x11
	domain=0, bus=0, slot=24, func=0
	class=07-80-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0006, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=16
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message, 64 bit
pci0:0:24:0: reprobing on driver added
found->	vendor=0x8086, dev=0x19de, revid=0x11
	domain=0, bus=0, slot=31, func=2
	class=05-80-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0006, statreg=0x0000, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
pci0:0:31:2: reprobing on driver added
found->	vendor=0x8086, dev=0x19df, revid=0x11
	domain=0, bus=0, slot=31, func=4
	class=0c-05-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0003, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=23
pci0:0:31:4: reprobing on driver added
ichsmb0: <Intel Denverton SMBus controller> port 0xefa0-0xefbf mem 0xdfe80000-0xdfe800ff irq 23 at device 31.4 on pci0
ioapic0: routing intpin 23 (PCI IRQ 23) to lapic 0 vector 66
smbus0: <System Management Bus> on ichsmb0
found->	vendor=0x8086, dev=0x19e0, revid=0x11
	domain=0, bus=0, slot=31, func=5
	class=0c-80-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0402, statreg=0x0000, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
pci0:0:31:5: reprobing on driver added
pci1: driver added
pci2: driver added
pci3: driver added
pci4: driver added
pci5: driver added
pci6: driver added
pci0: driver added
found->	vendor=0x8086, dev=0x19a2, revid=0x11
	domain=0, bus=0, slot=5, func=0
	class=08-07-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0004, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=23
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message, vector masks
pci0:0:5:0: reprobing on driver added
found->	vendor=0x8086, dev=0x19ac, revid=0x11
	domain=0, bus=0, slot=18, func=0
	class=08-80-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0006, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=16
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message, 64 bit, vector masks
pci0:0:18:0: reprobing on driver added
ismt0: <Atom Processor C3000 SMBus 2.0> mem 0xdfe7b000-0xdfe7b3ff irq 16 at device 18.0 on pci0
ismt0: attempting to allocate 1 MSI vectors (1 supported)
msi: routing MSI IRQ 310 to local APIC 8 vector 60
ismt0: using IRQ 310 for MSI
found->	vendor=0x8086, dev=0x19d3, revid=0x11
	domain=0, bus=0, slot=24, func=0
	class=07-80-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0006, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=16
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message, 64 bit
pci0:0:24:0: reprobing on driver added
found->	vendor=0x8086, dev=0x19de, revid=0x11
	domain=0, bus=0, slot=31, func=2
	class=05-80-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0006, statreg=0x0000, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
pci0:0:31:2: reprobing on driver added
found->	vendor=0x8086, dev=0x19e0, revid=0x11
	domain=0, bus=0, slot=31, func=5
	class=0c-80-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0402, statreg=0x0000, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
pci0:0:31:5: reprobing on driver added
pci1: driver added
pci2: driver added
pci3: driver added
pci4: driver added
pci5: driver added
pci6: driver added
smbus1: <System Management Bus> on ismt0
smb0: <SMBus generic I/O> on smbus0
smb1: <SMBus generic I/O> on smbus1
<118>Configuring IPsec VPN... 
<6>ipsec2000: bpf attached
<118>done
<118>Generating RRD graphs...done.
<118>Starting syslog...done.
<118>Starting CRON... done.
<118> Starting package IPsec Profile Wizard...done.
<118> Starting package acme...done.
<118> Starting package nmap...done.
<118> Starting package OpenVPN Client Export Utility...done.
<118> Starting package net-snmp...done.
<118> Starting package mtr-nox11...done.
<118> Starting package System Patches...done.
<118> Starting package FRR...done.
<118> Starting package iperf...done.
<118> Starting package Shellcmd...done.
<118> Starting /usr/local/etc/rc.d/net-snmpd.sh...done.
<118>Netgate pfSense Plus 21.05-DEVELOPMENT amd64 Wed Apr 21 01:03:58 EDT 2021
<118>Bootup complete
<6>ipsec2000: bpf attached


Fatal trap 12: page fault while in kernel mode
cpuid = 3; apic id = 1c
fault virtual address	= 0x4b
fault code		= supervisor read data, page not present
instruction pointer	= 0x20:0xffffffff811d74b0
stack pointer	        = 0x28:0xfffffe000053f540
frame pointer	        = 0x28:0xfffffe000053f590
code segment		= base 0x0, limit 0xfffff, type 0x1b
			= DPL 0, pres 1, long 1, def32 0, gran 1
processor eflags	= interrupt enabled, resume, IOPL = 0
current process		= 27 (dom0)
trap number		= 12
panic: page fault
cpuid = 3
time = 1619099402
KDB: enter: panic
