Regression #13993
closedSwitch ports on 7100/1100/2100 do not have Auto MDI-X support enabled
100%
Description
In 23.01 the 7100 switch ports do not support auto-MDI/X. A cross-over cable is required to link two ports on the switch or the switch port on two 7100s.
This is a regression since 22.05.
Files
LS Updated by Luiz Souza over 3 years ago
- Status changed from New to Feedback
- Assignee set to Luiz Souza
- % Done changed from 0 to 100
Fixed in 23.05 and also in the 23.01 branch.
JG Updated by Jordan G over 3 years ago
running version 23.05.a.20230224.0600 on 7100 I am again able to successfully connect with 1100, this was not working with both devices running 23.01
RC Updated by Ryan Coleman over 3 years ago
Luiz Souza wrote in #note-1:
Fixed in 23.05 and also in the 23.01 branch.
I don't see any recommended patches -- how does this get applied to existing 23.01 installations?
JP Updated by Jim Pingle over 3 years ago
Ryan Coleman wrote in #note-3:
Luiz Souza wrote in #note-1:
Fixed in 23.05 and also in the 23.01 branch.
I don't see any recommended patches -- how does this get applied to existing 23.01 installations?
It's a binary change so it requires a new build/kernel, it can't be patched on a running system that way.
RC Updated by Ryan Coleman over 3 years ago
Jim Pingle wrote in #note-4:
Ryan Coleman wrote in #note-3:
Luiz Souza wrote in #note-1:
Fixed in 23.05 and also in the 23.01 branch.
I don't see any recommended patches -- how does this get applied to existing 23.01 installations?
It's a binary change so it requires a new build/kernel, it can't be patched on a running system that way.
Ok so it is not available to 23.01 -- it would have to be a point release then?
JP Updated by Jim Pingle over 3 years ago
Ryan Coleman wrote in #note-5:
Ok so it is not available to 23.01 -- it would have to be a point release then?
Yes
JG Updated by Jordan G over 3 years ago
switch is not detected under interfaces menu with current build - 23.05.a.20230322.0600
DZ Updated by Danilo Zrenjanin over 3 years ago
- File textdump.tar.0 textdump.tar.0 added
Tested against 23.05.a.20230405.0600
The switch gets detected correctly and can negotiate the link with SG-1100 and SG-2100.
However, the system crashes after removing the cable from LAN (ETH2) switchport.
SW Updated by Steve Wheeler over 3 years ago
That's this netlink issue: https://redmine.pfsense.org/issues/14233
JG Updated by Jordan G over 3 years ago
Successfully linked 7100 to 1100 both on 23.05.a.20230407.0116
Switches are back in the interfaces menu on 7100 @ 23.05.a.20230407.0116 - changed PVID and tag/untag port selection without issue.
JP Updated by Jim Pingle over 3 years ago
- Related to Regression #14269: 1100/2100: switch ports not enabled for auto-mdi-x added
JP Updated by Jim Pingle over 3 years ago
- Subject changed from 7100: switch ports not enabled for auto-mdi-x to 7100/1100/2100: switch ports not enabled for auto-mdi-x
- Affected Architecture SG-1100, SG-2100 added
SW Updated by Steve Wheeler over 3 years ago
- Status changed from Feedback to Resolved
This is fixed in current snapshots. The switch ports link MDI and MDIX as expected.
The other issues reported here are unrelated.
Tested: pfSense-23.05.a.20230410.0600
JP Updated by Jim Pingle over 3 years ago
- Subject changed from 7100/1100/2100: switch ports not enabled for auto-mdi-x to Switch ports on 7100/1100/2100 do not have Auto MDI-X support enabled
Updating subject for release notes.