pfSense » pfSense Plus

Hello fellow Redmine community members, I found a bug during upgrade to 25.11 the upgrade fails with my NVMe driver.

Loading kernel...
/boot/kernel/kernel text=0x318 text=0xcbe8a8 text=0x14683e8 data=0x19cff0 data=0x0+0x2ca000 0x8+0x19d088+0x8+0x1b8d4c
Loading configured modules...
/boot/kernel/zfs.ko text=0xce1b0 text=0x220bd8 data=0x3b0f0+0xaad44 0x8+0x49380+0x8+0x302ef
/boot/kernel/opensolaris.ko text=0x195e text=0xbf0 data=0x4d0+0x1a030 0x8+0xf78+0x8+0x87b
can't find '/etc/hostid'
can't find '/boot/entropy'
Using DTB provided by EFI at 0x8000000.
---<<BOOT>>---GDB: current port: uart
KDB: debugger backends: ddb gdb
KDB: current backend: ddb
WARNING: DTB version is 6.4 while kernel expects 6.8, please update the DTB in the ESP
Copyright (c) 1992-2024 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 15.0-CURRENT #0 plus-RELENG_24_11-n256407-1bbb3194162: Fri Nov 22 05:12:13 UTC 2024
root@freebsd:/var/jenkins/workspace/pfSense-Plus-snapshots-24_11-main/obj/aarch64/KRivbaXa/var/jenkins/workspace/pfSense-Plus-snapshots-24_11-main/sources/FreeBSD-src-plus-RELENG_24_11/arm64.aarch64/sys/pfSense arm64
FreeBSD clang version 18.1.6 (https://github.com/llvm/llvm-project.git llvmorg-18.1.6-0-g1118c2e05e67)
VT: init without driver.
module scmi already present!
real memory = 3602862080 (3435 MB)
avail memory = 3461632000 (3301 MB)
Starting CPU 1 (1)
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
arc4random: WARNING: initial seeding bypassed the cryptographic random device because it was not yet seeded and the knob 'bypass_before_seeding' was enabled.
random: entropy device external interface
wlan: mac acl policy registered
kbd0 at kbdmux0
ofwbus0: <Open Firmware Device Tree>
simplebus0: <Flattened device tree simple bus> on ofwbus0
simplebus1: <Flattened device tree simple bus> on simplebus0
simple_mfd0: <Simple MFD (Multi-Functions Device)> mem 0x13800-0x138ff,0x13c00-0x13c1f on simplebus1
simple_mfd1: <Simple MFD (Multi-Functions Device)> mem 0x18800-0x188ff,0x18c00-0x18c1f on simplebus1
psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0
netgate0: <Netgate 2100>
netgate0: version: 0.1
gic0: <ARM Generic Interrupt Controller v3.0> mem 0x1d00000-0x1d0ffff,0x1d40000-0x1d7ffff,0x1d80000-0x1d81fff,0x1d90000-0x1d91fff,0x1da0000-0x1dbffff irq 27 on simplebus1
gpio0: <Armada 37x0 North Bridge GPIO Controller> mem 0x13800-0x138ff,0x13c00-0x13c1f irq 28,29,30,31,32,33,34,35,36,37,38,39 on simple_mfd0
gpiobus0: <OFW GPIO bus> on gpio0
gpio1: <Armada 37x0 South Bridge GPIO Controller> mem 0x18800-0x188ff,0x18c00-0x18c1f irq 40,41,42,43,44 on simple_mfd1
gpiobus1: <OFW GPIO bus> on gpio1
gpiomdio0: <GPIO MDIO bit-banging Bus driver> at pins 21,23 on gpiobus1
gpiomdio0: MDC pin: 21, MDIO pin: 23
a37x0-xtal0: <Marvell Armada 3700 Oscillator> mem 0x13800-0x138ff,0x13c00-0x13c1f on simple_mfd0
generic_timer0: <ARMv8 Generic Timer> irq 0,1,2,3 on ofwbus0
Timecounter "ARM MPCore Timecounter" frequency 12500000 Hz quality 1000
Event timer "ARM MPCore Eventtimer" frequency 12500000 Hz quality 1000
a37x0_tbg0: <Marvell Armada 3700 time base generators> mem 0x13200-0x132ff on simplebus1
a37x0_nb_periph_driver0: <marvell,armada-3700-nb-periph-clock> mem 0x13000-0x130ff on simplebus1
a37x0_sb_periph_driver0: <marvell,armada-3700-sb-periph-clock> mem 0x18000-0x180ff on simplebus1
cpulist0: <Open Firmware CPU Group> on ofwbus0
cpu0: <Open Firmware CPU> on cpulist0
pmu0: <Performance Monitoring Unit> irq 4 on ofwbus0
spi0: <Armada 37x0 SPI controller> mem 0x10600-0x10fff irq 6 on simplebus1
iichb0: <Marvell Armada 37x0 IIC controller> mem 0x11000-0x11023 irq 7 on simplebus1
iicbus0: <OFW I2C bus> on iichb0
iic0: <I2C generic I/O> on iicbus0
iichb1: <Marvell Armada 37x0 IIC controller> mem 0x11080-0x110a3 irq 8 on simplebus1
iicbus1: <OFW I2C bus> on iichb1
iic1: <I2C generic I/O> on iicbus1
nxprtc0: <NXP PCF8563 RTC> at addr 0xa2 on iicbus1
gpio2: <ISSI IS31FL3199 9 channel light effect LED driver> at addr 0xce on iicbus1
gpiobus2: <OFW GPIO bus> on gpio2
gpioc2: <GPIO controller> on gpio2
uart0: <Marvell Armada 3700 UART> mem 0x12000-0x121ff irq 9,10,11 on simplebus1
uart0: console (115200,n,8,1)
gpioc0: <GPIO controller> on gpio0
gpioc1: <GPIO controller> on gpio1
mvneta0: <NETA controller> mem 0x30000-0x33fff irq 14 on simplebus1
mvneta0: version is 10
miibus0: <MII bus> on gpiomdio0
mv88e151x0: <Marvell 88E1512 Gigabit PHY> PHY 1 on miibus0
mv88e151x0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, 1000baseSX, 1000baseSX-FDX, auto
mvneta0: Ethernet address: 90:ec:77:0d:da:25
mvneta1: <NETA controller> mem 0x40000-0x43fff irq 15 on simplebus1
mvneta1: version is 10
mdio0: <MDIO> on mvneta1
mdioproxy0: <MII/MDIO proxy, MDIO side> on mdio0
e6000sw0: <Marvell 88E6141> on mdio0
e6000sw0: single-chip addressing mode
e6000sw0: PHY at port 1
miibus1: <MII bus> on e6000sw0
e1000phy0: <Marvell 88E1000 Gigabit PHY> PHY 17 on miibus1
e1000phy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
e6000sw0: PHY at port 2
miibus2: <MII bus> on e6000sw0
e1000phy1: <Marvell 88E1000 Gigabit PHY> PHY 18 on miibus2
e1000phy1: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
e6000sw0: PHY at port 3
miibus3: <MII bus> on e6000sw0
e1000phy2: <Marvell 88E1000 Gigabit PHY> PHY 19 on miibus3
e1000phy2: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
e6000sw0: PHY at port 4
miibus4: <MII bus> on e6000sw0
e1000phy3: <Marvell 88E1000 Gigabit PHY> PHY 20 on miibus4
e1000phy3: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
e6000sw0: CPU port at 5
e6000sw0: fixed port at 5
e6000sw0: switch is ready.
etherswitch0: <Switch controller> on e6000sw0
mvneta1: Ethernet address: 90:ec:77:0d:da:26
xhci0: <Generic USB 3.0 controller> mem 0x58000-0x5bfff irq 16 on simplebus1
xhci0: 32 bytes context size, 32-bit DMA
usbus0 on xhci0
ehci0: <Marvell Integrated USB 2.0 controller> mem 0x5e000-0x5ffff irq 17 on simplebus1
usbus1: EHCI version 1.0
usbus1 on ehci0
sdhci_xenon0: <Armada Xenon SDHCI controller> mem 0xd8000-0xd82ff,0x17808-0x1780b irq 25 on simplebus1
mmc0: <MMC/SD bus> on sdhci_xenon0
ahci0: <AHCI SATA controller> mem 0xe0000-0xe1fff irq 26 on simplebus1
ahci0: AHCI v1.30 with 1 6Gbps ports, Port Multiplier supported with FBS
ahcich0: <AHCI channel> at channel 0 on ahci0
pcib0: <Marvell Armada 3700 PCIe Bus Controller> mem 0xd0070000-0xd008ffff irq 5 on simplebus0
pcib0: link up
pci0: <OFW PCI bus> on pcib0
nvme0: <Generic NVMe Device> mem 0xe8000000-0xe8003fff at device 0.0 on pci0
Fatal data abort:
x0: 0x0000000000000000
x1: 0x00000000e8000000
x2: 0x0000000000000000
x3: 0x0000000000000000
x4: 0x0000000000020000
x5: 0x0000000000000006
x6: 0x0000000000000002
x7: 0xffff0000022c9520 (initstack + 0x3520)
x8: 0xffff000002221b00 (memmap_bus + 0x0)
x9: 0xffff000000b6a350 (generic_bs_r_4 + 0x0)
x10: 0xffff00000219e3b8 (bus_get_domain_desc + 0x0)
x11: 0xffff00000219e3b8 (bus_get_domain_desc + 0x0)
x12: 0xffff0000021b1ba8 (lock_class_mtx_spin + 0x0)
x13: 0xfefefefefeff0f00
x14: 0x0000000000000000
x15: 0x0000000000000000
x16: 0xffff0000006bc734 (bus_generic_get_domain + 0x0)
x17: 0x0000000000000000
x18: 0xffff0000022c95a0 (initstack + 0x35a0)
x19: 0xffff00009cc50000 ($d.6 + 0x99ebe5b8)
x20: 0xffffa00001c83200
x21: 0xffff00009cc50048 ($d.6 + 0x99ebe600)
x22: 0xffff00009cc69000 ($d.6 + 0x99ed75b8)
x23: 0xffff00009cc50068 ($d.6 + 0x99ebe620)
x24: 0xffffa00001c83300
x25: 0xffff000000cf4c5b (notify.prefix + 0x326f7)
x26: 0xffffa000019478a0
x27: 0xffffa000015c7620
x28: 0x0000000000000002
x29: 0xffff0000022c9620 (initstack + 0x3620)
sp: 0xffff0000022c95a0
lr: 0xffff0000002f7e38 (nvme_ctrlr_construct + 0x70)
elr: 0xffff000000b6a358 (generic_bs_r_4 + 0x8)
spsr: 0x00000000600000c5
far: 0x00000000e8000000
esr: 0x0000000096000004
panic: vm_fault failed: 0xffff000000b6a358 error 1
cpuid = 0
time = 1
KDB: enter: panic
[ thread pid 0 tid 100000 ]
Stopped at kdb_enter+0x48: str xzr, [x19, #2944]
db>


Can we add a script that auto disables the driver until after the install is complete ? I use this drive over movie adapter to NVMe m.2

set hint.nvme.0.disabled=1
boot


Ref:
https://forum.netgate.com/topic/195988/2100-max-upgrade-24-03-to-24-11-failed