pfSense

Correctly check the secondary/primary parameter setting on dhcp failover configuration

Correct typo that prevents dhcp rules from properly being generated.

Do not include disabled OpenVPN in vpn_networks and negate_networks

Fix errant display of "0 table deleted" during filter reload on console.

Remove unecessary capitalized WARNING from disabled APC message

Do not sync DHPCv6, it must operate independetly. Ticket #3184

Remove failover peer IP settings from DHCPv6, DHCPv6 doesn't support failover the way that DHPv4 did. Fixes #3184

Disable kill_states by default on upgrade, it fixes #3183

Allow for easier override on $g values if needed.

Correct check to match the right vip based on configured ip. Reported-by: http://forum.pfsense.org/index.php/topic,66234.0.html

Ticket #3181 do the state flushing only on down gateway detection rather than any time.

When the v4 wan is dynamic and v6 is type dhcp and v6 information is retrieved through v4 link than trigger dhcp6c reconfiguration.

Actually the / here is not needed.

Introduce two new functions to be used on locking.

- try_lock: used for trying to get an EXCLUSIVE lock for a specified timeout by default of 5
- unlock_force: which just releases any locks held on a specified lock

Use this new functions on rc.openvpn to avoid spurious stale locks around.

Add safety belts to code in rc.openvpn to avoid php errors to leave stale locks around

Make the operation of saving old rule nearby the writing operation to be logical to spot

Sprinkle some unsets to reduce footprint and correct some whitespaces

filter_generate_port error log function name

Absolutely minor adjustment to make the error log message refer to the new function name.

Fixes #3173 if any port information exists on the rule than put it on the NEGATE rule generated.

Remove SPD when disable phase2, it fixes #2719

Merge pull request #786 from individual-it/master

Increased needed memory for APC to 512M + code cleanup

Merge pull request #796 from phil-davis/master

Traffic Shaper GUI text typos

Merge pull request #793 from shahidsheikh/master

Fix #3174 Handling of gateway groups in openvpn_restart()

Bring back static routes to fix issues reported on Ticext #3179

Correct typo on variable name

Fix #3004:

. Create a function to replace strings on deep associative arrays
. Use the recent created function array_replace_values_recursive to fix
VIP interface names instead of touch config.xml directly

Make sure RRD data is restored from backup before upgrading data and a new backup is done after. It should fix #2159

Traffic Shaper GUI text typos

and note the Queue Limit is a number of packets (not packets per second)

Resolves #3177. Do a filter reconfigure if the dynds ipsec hosts are present and being reloaded.

touch up text, s/nat/NAT/

Fix #3174 Handling of gateway groups in openvpn_restart()
If the underlying vip of a gateway group that an openvpn client is bound
to is in backup mode then the client should not start.

shaper burst may be blank, but if not then must be numeric

Fix #3172, return_gateway_groups_array() was returning the last vip since it was using wrong variable name on iteration

Dummynet does not require burst size specification

Dummynet traffic shaper does not require burst size specification and
assumes 0 if not specified. Allow user to leave burst field blank/

Provide get_uptime_sec in a common include file

so it is available to anything that cares.

Increased needed memory for APC to 512M + code cleanup

- Increased the needed memory for APC to 512M as we often run into memory problems on our 256M box
- fixed the RAM calculation to divide by 1024 and not 1000
- code cleanup (renaming variables and creating new to avoid magic numbers)

Use physmem and realmem from get_memory() in the appropriate places

Use new names for get_memory parameters

Use hw.physmem when calculating pfsense_default_state_size

hw.physmem is the actual amount of memory that FreeBSD/pfSense can get its hands on, so use this for the calculation.

Use updated get_memory var names

The value of minimum_ram_warning is designed to be compared to hw.physmem - so do that. Usse the appropriate physmem or realmem value in each place.

Improve var names in get_memory

realmem is the amount of actual (real) memory installed - the size of the RAM card - e.g. 256MB
physmem is the amount of memory available to FreeBSD after BIOS, video... has stolen some of realmem.
The variable names currently used are not very helpful for code readability. This standardises them. No functional change here.

s/require/require_once/g for filter.inc to avoid redeclaration errors in some rare cases.

Support the names used by the status page as well as those used internally by service entries.

Delete old route for remote gateway when its IP changes. It fixes #3155

Fixup check for existing easyrule block rule to account for the ipproto and when the ipproto is blank.

Add scope to target when it is a link-local, it helps ticket #3150

Attempt to recognize pfsync entries from pf logs.

Fix selection of IPv6 target IP for IPv6 Outbound NAT rules.

This makes it possible (without source hacking) to do many:1 NAT of IPv6.

Some will rejoice. Some will curse.

This should really only be done in limited, specific circumstances. Don't develop the IPv4 NAT mentality with IPv6.

Obsolete more ntp binaries from base

Use ntpdate from ports also and obsolete base one

Ooops fix this to add only th einterface

Obsolete base ntpd since we are using the one from ports

Add scope identifier to target when its link-local

Add also a special case so the correct ip is returned for the case when WAN is v4 PPP type and v6 is DHCP but with option fetch v6 info from v4.

When using DHCPv6 and only requesting a prefix the communication on the WAN interface will be over link-local so return the link-local address of the interface in this case rather than nothing.

Optimize a bit to try and convrt back to friendly interface only when needed

Resolves #2627. When WANv4 is PPP and v6 is DHCP but the option get v6 info from v4 is ticked the real interface is different. For WANv4 is pppXX and for v6 is the real underlying interface. Take this into consideration during interface_bring_down to properly cleanup things

Correctly remove IPv6 addresses from the interface rather than just erroring out. The same trick that works for IPv4 of not specifying address does not work with v6

Even if called with wrong parameters try to do something rather than return here.

Add the check even here when dealing with ipv6 addreses

Handle link local addresses with embedded interface scope on is_ipaddrv6 and also on dnsmasq which is not yet there for these addresses

Unbreak limitrules and probably pfblocker errors. Spotted-by: Jim

When renaming or deleting a virtual server, clean up the old relayd anchor name. Otherwise the rules are still there and valid, and will cause problems as they will override the new VS settings. Also clear out the anchors when stopping relayd or starting fresh that way no old settings could conflict.

Synchronize dhcpv6 as well if dhcp sync setting is on. Reported-by: http://forum.pfsense.org/index.php/topic,65487.0.html

Cleanup some code that is not needed anymore

Use pfSense module functions for finding interface v6 addresses. The addresses will be not in friendly format as returned by getnameinfo

Remove prior CSC entry when cleaning up. Fixes #3143

Declare globals as global before defining them in openvpn.inc

Force apinger to write the status file before getting gateway status

Ticket #3139 try to detect if the popen is closed from an error

Fix interface selections on UPnP to show the customized descriptions entered by the user. While here, add an external interface selection knob. Fixes #3141

Conflicts:

etc/inc/pkg-utils.inc

Fix #1047

• When advanced options (LRO, TSO and CSUM) changes, enable capabilities
  again on interfaces
• For lagg and bridge, check caps instead of encaps and enable flags
  when it's necessary for all members
• Take in consideration Disable (LRO, TSO, CSUM) options from...

Remove duplicate polling set

Show apinger as a service when active, and display its status on gateway-related pages.

Don't print this message for a mobile IPsec setup. It's normal for it to not have an endpoint, and not worth spamming the log about.

Try to do the loading operations as close as possible to avoid any issues coming from it

Correct bandwidth assignment so the configuration is not reverted courtesy of ipfw(4) swapped arguments. Reported-by: http://forum.pfsense.org/index.php/topic,65069.0.html

Reload apinger now that we can rather than restarting. Related to Ticket #3119

fix text - s/occured/occurred/

the state type is required/valid for all specifications of protocol, not
just the ones formerly listed. For instance, sloppy is valid (and widely
used on 2.0.x and some older 2.1x) with "any" protocol.

Resolves #3121. Fix the command so it does perform correctly

Manually revert the patch to cleanup aliases since now its propely handled in the ip assignements. Ticket #2495

Add Zone to the messages logged on syslog from CP to easy troubleshooting

Reorder reverse lookup overrides so user-specified ones are effective

If the user specifies a domain override for 10.in-addr.arpa and also specifies "Do not forward private reverse lookups" then the user-specified entry is not effective. But the code was supposed to allow users to specify individual reverse lookup domain overrides that took precedence....

Fix up filter_pflog_start - optimize some code, and fix $retval so that it will be restarted correctly after killing it.

Show the name of the unresolvable alias name as well as the rule description to avoid ambiguity.

use correct domain names when registering static DHCP entries in DNS

When registering static DHCP entries in DNS, we first try to use the domain name configured for the static entry (if any), then the domain name configured in the DHCP server settings for the corresponding interface (if any), and as a last resort the system domain name....

Fix #3113, fix multiple english spell errors s/seperet/separat/

Optimization has nothing to do with limits

Fix #3106, parse 'not' rules right on destination for port forward + reflection proxy rules

Allow advanced options state-related parameters to be used for TCP, UDP and ICMP

Allows the state-related parameters to be specified for UDP and ICMP as well as TCP. Discussed in forum http://forum.pfsense.org/index.php/topic,64653.0.html

Update rrd.inc

Fix this error
php: rc.bootup: The command '/usr/bin/nice -n20 /usr/local/bin/rrdtool update /var/db/rrd/system-mbuf.rrd N:U:U:U:U:U' returned exit code '1', the output was 'ERROR: expected 4 data source readings (got 5) from N:U:U:U:U:U'

Implement an option to allow using the IPv4 connectivity interface for sending the dhcpv6 information. Usually useful for ppp[oe] type links and some ISP

Add missing backup of gettytab

Merge pull request #718 from N0YB/Advanced_DHCP_Client_Options

Fix required options syntax typo

Fix required options syntax typo

3652 days worth is a too much. Scale it back to more reasonable 1.25 x maximum used data (2284 days).

Handle IPv6 in ip_in_interface_alias_subnet()

Merge pull request #714 from phil-davis/master

Minimize inclusion of bogonsv6

Disable the BEAST protection by default because the GUI will break if you use this and have a Hifn card installed. Others may break similarly. Change it into a checkbox option, off by default, and automatically disable it if a conflicting card has been detected.